Avaya DEFINITY Server R Скачать руководство пользователя страница 261 | Manualshive

Страница: 261 / 550

background image

Remove Module Control Carrier(s)

Issue 7 November 2003

5-71

555-233-115

Remove CURL from Module Control Carrier A

Remove the CFY1 current limiter (CURL) from the pin-field block marked “CURL”
on the “A” carrier. The CURL will be reused in the EPN.

NOTE:

Note the position of the components on the left side of the CURL.

NOTE:

Verify that the CURL meets the minimum usable vintage requirements.

Remove Module Control Carriers A and B

1. Remove the TDM/LAN cable from between the “A” and “B” carriers. See

. This cable will be reused.

2. Disconnect 1 end of the TDM/LAN cable (between the “A” and “D” carriers)

from the “A” carrier. Leave the other end connected to the “D” carrier, and
move the cable into a position so that it will not interfere with removing the
“A” carrier.

NOTE:

Note the position of the TDM/LAN cable before disconnecting.

3. Disconnect 1 end of the TDM/LAN cable (between the “B” and “C” carriers)

from the “B” carrier. Leave the other end connected to the “C” carrier, and
move the cable into a position so that it will not interfere with removing the
“B” carrier.

!

CAUTION:

When removing the TDM/LAN cables from a previously upgraded
carrier, be careful that none of the short pieces of shrink tubing come
off the 4 corner pins of the pin-field block. Otherwise, when the new
equipment is connected, -48 volts could short to ground.

4. Remove and retain the 8 ground straps from between the “A” and “B”

carriers. See

5. Disconnect 1 end of the 8 ground straps from between the “A” and “D”

carriers. These straps will reconnect to the new “A” carrier.

6. Disconnect 1 end of the 8 ground straps from between the “B” and “C”

carriers. These straps will reconnect to the new “B” carrier.

7. Disconnect the “P1” (small 9-pin) connector and the “P2” (large 38-pin)

connector from the “A” carrier. See

. Move the cables into a

position where they will not interfere with removing the carrier.

8. Slide the latch up, and disconnect the “P1” (small 9-pin) connector from the

“B” carrier. Move the cable into a position where it will not interfere with
removing the carrier.

«
...
259
260
261
262
263
...
»

Содержание DEFINITY Server R







































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DEFINITY Server R

Бренд: Balluff Страницы: 62

Бренд: Avalue Technology Страницы: 12

Бренд: MIPS Страницы: 10

Бренд: DFI Страницы: 104

Бренд: Analog Devices Страницы: 13

Бренд: Gigabyte Страницы: 96

Бренд: Supero Страницы: 80

Бренд: Texas Instruments Страницы: 18

Бренд: H-Tec Страницы: 28

C807MS-E33 Series

Бренд: MSI Страницы: 124

Бренд: TYAN Страницы: 164

Бренд: Safran Страницы: 29

Бренд: Texas Instruments Страницы: 51

Бренд: Texas Instruments Страницы: 20

Бренд: Intel Страницы: 1

Бренд: IEI Technology Страницы: 164

Бренд: Infineon Страницы: 30

Бренд: Winmate Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды