background image

SPECIFICATIONS 

 
STEALTH 

 

 

 

 

300.S 

 

400.S 

 

500.S 

 
*Audio power output per Channel, 
both channels driven at 14.4VDC. 
 

- 4 ohm Stereo, 12.0volt 20Hz-20kHz <.018%THD 

50watts/ch 

75watts/ch 

150watts/ch 

 

- 2 ohm Stereo, 14.4volt 20Hz-20kHz <.02%THD

 

108w/ch  

150w/ch  

320w/ch 

 

- 1 ohm Stereo, 14.4volt 20Hz-20kHz <.05%THD

 

182w/ch  

236w/ch  

400w/ch 

 
* Signal to Noise Ratio 

 

 

 

 

 

>90dB 

 
* Frequency Response 

10Hz-40kHz, 

?

 1dB 

 
* Crossover: Separate 

 

 

 

 

 

 
- High Pass 

75Hz-750Hz Variable 

 
- Low Pass 

40Hz-150Hz Variable 

 
- Slope 

0-12db OCTAVE 

 
- Subsonic Filter 

35Hz (-3dB) 

 
- Bass Boost 

0-18dB Variable 

 
* Input Sensitivity 

200mV-4Volts Variable 

 
* Input Impedance 
 
- Low level input 

22KI ohms  

 
* Damping Factor 

180 into 4 ohms  

 
* Channel Separation 

>70dB 

 
* Power Supply Consumption 
(Bridge RMS) 

 

 

 

 

27A 

 

36A 

 

76A 

 
* Fuse Rating 

 

 

 

 

15Ax2 

 

20Ax2 

 

40Ax2 

 
* Dimension (W   

 

 

 

10.5” 

 

10.5” 

 

10.5” 

 

* Dimension (

x H   

 

 

 

2.3” 

 

2.3” 

 

2.3” 

 

* Dimension (

x L inch) 

 

 

 

13” 

 

13.8” 

 

17.3” 

 
** 1. These specifications can be changed without notice. 

**

 2. Please note that the features shown in this manual may vary from model to model. 

 

Содержание 300. S












Отзывы: