autosen AF004 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 42

background image

8

4.3 Applications

• Water, water-based media
• Oils, oil-based media (only for operation with coaxial probe)
Application examples:

•  Detection of coolant emulsion in a machine tool�
•  Detection of cleaning liquid in a parts cleaning system�
•  Monitoring of hydraulic oil in a hydraulic power unit (only for operation with

coaxial probe)�

4.3.1 Restriction of the application area

Incorrect measurements or signal loss may be caused by the following

media:

-Highly absorbing surfaces (e�g� foam)�
-Intensely bubbling surfaces�
-Media which are very inhomogeneous, separate from each other thus

forming separation layers (e�g� oil layer on water)�

► Check the function by performing an application test�

► Installation in a steady area (→ 6.1).

> In case of signal loss, the unit displays [E�033] and switches the

outputs to a defined state (→ 11.5).

• The unit is not suitable for bulk materials (e�g� plastic granulates)�
• If the unit is to be used in acids or alkalis, in hygienic areas or in electroplating

applications: first check the compatibility of the product materials (→ 12

Technical data and scale drawing) with the media to be monitored�

• The unit is not suitable for applications where the probe is subjected to

permanent and high mechanical stress (e�g� strongly moving viscous media or

strongly flowing media)�

• In case of operation with single probe: use preferably in metal tanks� When

installed in plastic tanks, deterioration caused by electromagnetic interference

may occur (noise immunity according to EN61000-6-2)�

Corrective measures: → 6.4.4.

• In case of operation with coaxial probe: not suitable for soiled or viscous media

and media prone to formation of deposit�

Maximum viscosity: 500 MPa · s�

«
...
6
7
8
9
10
...
»

Содержание AF004











































Отзывы:

Нет отзывов

Похожие инструкции для AF004

Бренд: Dakota Digital Страницы: 2

Бренд: Dakota Digital Страницы: 6

Бренд: Dakota Digital Страницы: 7

Бренд: Dakota Alert Страницы: 2

Wireless Temperature/Humidity Station

Бренд: DAVIS Страницы: 8

Бренд: Yakima Страницы: 11

Бренд: Hama Страницы: 10

Бренд: Hama Страницы: 6

Бренд: IFM Страницы: 12

Бренд: IFM Страницы: 13

Efector 200 Series

Бренд: IFM Страницы: 4

Бренд: IFM Страницы: 33

Alerts TX60U-IT

Бренд: La Crosse Technology Страницы: 3

HOIST-A-TOP JL CRANK

Бренд: Lange Originals Страницы: 13

Бренд: LAZER Страницы: 19

Audio Interface Conectiv

Бренд: M-Audio Страницы: 18

Бренд: Valcom Страницы: 1

Бренд: Valcom Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды