autosen AF004 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 42

background image

12

5.2.6 Safe state

• In case of a fault a safe state can be defined for each output�
• If a fault is detected or if the signal quality is below a minimum value, the

outputs pass into the "safe state"� For this case the response of the outputs can

be set via the parameters [FOU1], [FOU2]�

• Temporary loss of signal caused e�g� by turbulence or foam formation can be

suppressed by a delay time (→ 10.5.6 [dFo]). During the delay time the last

measured value is frozen� If the measured signal is received again in sufficient

strength within the delay time, the unit continues to work in normal operation�

If, however, it is not received again in sufficient strength within the delay time,

the outputs pass into the safe state�

In case of heavy foam formation and turbulence, note the examples of how

to create a steady area (→ 6.1.2).

5.3 IO-Link
General information

This unit has an IO-Link communication interface which requires an IO-Link-

capable module (IO-Link master) for operation�
The IO-Link interface enables direct access to the process and diagnostic data

and provides the possibility to set the parameters of the unit during operation� In

addition communication is possible via a point-to-point connection with a USB

adapter cable�
Further information about IO-Link is available at www� �com�

Device-specific information

You will find the IODDs necessary for the configuration of the IO-Link unit and

detailed information about process data structure, diagnostic information and

parameter addresses at www�autosen�com�

Parameter setting tools

You will find all necessary information about the required IO-Link hardware and

software at www�autosen�com�

«
...
10
11
12
13
14
...
»

Содержание AF004











































Отзывы:

Нет отзывов

Похожие инструкции для AF004

Бренд: A-Tach Mounts Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

Бренд: Garmin Страницы: 14

Бренд: J-Top Страницы: 2

Бренд: RAKINDA Страницы: 20

Бренд: ZALMAN Страницы: 20

Бренд: Gamko Страницы: 32

Бренд: Salta Страницы: 76

Бренд: Saft Страницы: 52

Бренд: Zebronics Страницы: 6

Бренд: ipf electronic Страницы: 4

Бренд: Berkefeld Страницы: 12

IR 2.0 12-24Vdc

Бренд: DOMUS LINE Страницы: 9

Бренд: Dometic GROUP Страницы: 20

Бренд: Cobra Страницы: 2

Бренд: Stobag Страницы: 3

PowerPack TPB-2112

Бренд: texet Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды