-|Transparent Guide|-
Product Components
• Product
•
Connector cable
• Instruction manual
Circuit
■ NPN open collector output
■ PNP open collector output
CIRC
UIT
LOAD
OCP
SCP
Max. 100 mA
Input Circuit
Input Circuit
CIRC
UIT
LOAD
OCP
SCP
Max. 100 mA
•
OCP (over current protection), SCP (short circuit protection)
Connections
12-24 VDCᜡ
NPN
LOAD
Brown
Black
Blue
White
External input
12-24 VDCᜡ
PNP
LOAD
Brown
Black
Blue
White
External input
•
The duration of a signal over 2 ms is necessary for the external input function.
For using the external input,use a photocoupler or external controller, etc.
Otherwise, it may result in product damage.
Dimensions
•
Unit: mm, For the detailed drawings, follow the Autonics website.
10
11.3
6.1
70.5
48.9
12.1
1.9
3
17.3
26.8
30.6
Ø2.5
Ø2.8
Sold Separately
•
Fiber optic units
Ordering Information
This is only for reference, the actual product does not support all combinations.
For selecting the specified model, follow the Autonics website.
BFX
-
D1
-
❶
❶ Control output
N: NPN open collector output
P: PNP open collector output
Max. 100 mA
Max. 100 mA
Error
Error
Cause
Troubleshooting
ERR
In RUN mode, the overcurrent has been
detected from the output circuit.
Remove the overcurrent due to the
overload.
RUN
[MODE] 3 sec
→
Program mode
[MODE] 3 sec
→
RUN
[SET]
→
Teaching sensitivity setting
Auto
→
[◀] + [▶
]
→
Manual sensitivity setting
[MODE] or
after 3 sec
→
[SET] + [▶
]
→
Anti-saturation function
Auto
→
[MODE]
→
Incident light level monitoring
[MODE]
→
[MODE] 7 sec
→
Initialization
Auto
→
Enter the Mode
• For more detailed information on functions and settings, refer to the manual.
Specifications
Model
BFX-D1-□
Light source
Red LED
Peak emission
wavelength
660 nm, modulated
Response time
Standard (500 ㎲
)
, Long distance (4 ms), Ultra long distance (10 ms),
Ultra fast (50 ㎲
)
, Fast (150 ㎲) mode
Sensitivity setting
Manual, Teaching (Auto-tuning, 1-point, 2-point, positioning)
Operation mode
Light ON, Dark ON
Measured value display
7-segment LCD, 4-digit (decimal, percentage)
Operation mode
of the timer
OFF, OFF Delay, ON Delay, One-shot
External input
Teaching sensitivity, initialization of the incident light level, emitter OFF,
control output setting, energy saving mode release
Indicator
Operation indicator (red),
display screen (PV display part: red LED, SV display part: green LED)
Approval
ᜢ ᜫ
Unit weight (packaged)
≈ 16 g (≈ 115 g)
Power supply
12-24 VDCᜡ ±10% (ripple P-P: ≤ 10%)
Current consumption
≤ 50 mA
Control output
NPN open collector output / PNP open collector output model
Load voltage
≤ 24 VDCᜡ
Load current
≤ 100 mA
Residual voltage
NPN: ≤ 1 VDCᜡ, PNP: ≤ 3 VDCᜡ
Protection circuit
Reverse power protection circuit, output short overcurrent protection
circuit, surge protection circuit
Insulation resistance
≥ 20 MΩ (500 VDCᜡ megger)
Dielectric strength
1,000 VACᜠ 50 / 60 Hz for 1 min
Vibration
1 mm double amplitude at frequency 10 to 55 Hz (for 1 min)
in each X, Y, Z direction for 2 hours
Shock
500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times
Ambient illuminance
(receiver)
Sunlight: ≤ 11,000 lx, incandescent lamp: ≤ 3,000 lx
Ambient temperature
01)
-10 to 50 ℃, storage: -20 to 70 ℃ (no freezing or condensation)
Ambient humidity
35 to 85%RH, storage: 35 to 85%RH (no freezing or condensation)
Protection rating
IP40 (IEC standard)
Connection
Connector cable
Cable spec.
Ø 4 mm, 4-wire, 2 m
Wire spec.
AWG22 (0.08 mm, 60-core), insulator outer diameter: Ø 1.25 mm
Tightening torque for
fiber optic unit
≥ 2kgf
Material
Case: POK, cover: PC
01) 1 to 2 units: -10 to 50 ℃, 3 to 8 units: -10 to 35 ℃
Be cautious about the heat transfer when the number of connected units is more than 8.
The ambient temperature varies with the number of connected amplifiers that are mounted on the DIN rail.
Be sure to check the temperatures when installing in the enclosed area.
