background image

DPM3-E Electrical User Manual, 1st Edition

User Manual - DPM3-E Series Electrical Panel Meters

13

will be able to take a value in the range -19999 to 19999, without taking into account the 

decimal point. In these case the first digit shows 0, 1, -1, 2, 3 or -.
Completion of each submenu routine returns the meter to 

Pro

 mode. To save data entered or 

changed during configuration press the 

ENTER

 key while in 

Pro

 mode. 

StorE

 will be displayed 

for a few seconds while all of the configuration data is stored in memory. The meter will then 

return to 

RUN

 mode.

Input Configuration

The figure below shows the input configuration menu. Divided into four submenus, each one 

of them separated by the dotted line in the manual, each menu corresponds to the programming 

of the different types of input: Volt dc, Volt ac, Amp dc, Amp ac. Once the type of signal has 

been selected you have then to select the range. Usually the 100, 60, 50mV (nU) ranges are 

shunts signals. . 

ENTER:

 Vertical displacement.

UP: 

Changes active digit.

SHIFT: 

Horizontal displacement.

Programming Keys

(Bottom view)

CnInP

U-dC

U-AC

A-dC

A-AC

600 U

PRO

200 U

20 U

2 U

5 A

1 A

0.2A

100nU

60nU

50nU

Содержание ProSense DPM3-E Series




























Отзывы: