Automation Direct PSM24-BCM360S Скачать руководство пользователя страница 7

RHINO Battery Control Module PSM24-BCM360S Operating Instructions
4th Edition 06/18

1 - 8 0 0 - 6 3 3 - 0 4 0 5

7

General Specifications

Battery Protection

Over voltage, deep discharge, overcharge, short-circuit and reverse connection (built-in fuse)

Status Signals

DC-OK input, DC-OK output, BAT OK all relay contact closed at status OK; All LEDs on (green) at status OK

Rating per Relay Contact

30 VDC / 0.6 A max.

Remote Link Wire 0.5m

One cable included with PSM24-BCM360S module

Remote ON/OFF

by external contact:  ON =  J5.7 + J5.8 not shorted 

OFF = J5.7 + J5.8 shorted

Temperature

Operating (ambient): -25°C to + 70°C max (-13°F to 158°F). Above +40°C(104°F) load derating 1.5%/°C 

Storage (non-operating): -25°C to + 85°C max (-13°F to 185°F). 

Temperature drift:  0.02%/°C.   

Cooling: convection, no internal fan

Humidity

95% (non-condensing) relative humidity maximum

Isolation

According to IEC/EN 60950-1, UL 60950-1, EN50178, EN60204

Over-temperature Protection

When the TS-1 cable is used, the battery charging function will stop if the temperature sensor indicates the battery is over temperature. When the 

temperature sensor detects that the temperature has returned to a safe range, normal battery charging operation will automatically restart.

Vibration 

IEC 60068-2-6: 3 axis, sine sweep, 10-55 Hz, 1g, 1 oct/min

Shock

IEC 60068-2-27: 3 axis, 15g half sine, 11ms

Enclosure Rating

IP20 (IEC 529)

Enclosure Material

Aluminum (chassis) / zinc plated steel (cover)

Mounting

Snap-on with self-locking spring for 35mm DIN rails per EN 50022-35x15/75, or wall mount with bracket (PSM-PANEL1 sold separately)

Connection

Pluggable screw terminals (plugs included) 2 terminals per output

Note: Unless otherwise stated, all specifications are valid at nominal input voltage, full load and +25°C after warmup time.

General Specifications   –  Safety Standards

Specification

Standard

Document Number

Electromagnetic Compatibility (EMC), Emissions

EMC, Emissions

Corresponds to connected units ( no internal switching device)

Electromagnetic Compatibility (EMC), Immunity

EMC, Immunity

Corresponds to connected units ( no internal switching device)

Pollution Degree

2

Front view

Side view

Top view

Bottom view

DC Input OK

Bat. OK

DC Output OK

Remote On/Off

Temp. Sensor

(TS)

1

2

3

4

5

6

7

8

9

10

Unit: mm [inches]

PSM24-BCM360S Dimensions

General Specifications

Содержание PSM24-BCM360S









Отзывы: