Automatic Technology SYNCRO ATS-3V3 Скачать руководство пользователя страница 29

Страница: 29 / 29

Automatic Technology office location

Head Office

6-8 Fiveways Blvd, Keysborough 3073

Phone (03) 9791 0200

ata-aust.com.au

Prefixed trademarks are the property of Automatic Technology (Australia) Pty Ltd
ABN 11 007 125 368. © 2020 Automatic Technology Australia Pty Ltd.

ATS Series Installation Manual

G - Setting up Tilt Door

Prior to limit set up, the opener can be set to J-Type Tilt Profile.

This process allows the opener to pre-set to J-Type settings

where the limit is not greater than 1500mm.

In JTYPE Mode the drive speed is reduced

and cannot be adjusted.

tip

S T E P O N E

S E T T I N G U P T I L T D O O R

S T E P T W O

To activate JTYPE Mode

Press together and opener

will beep TWICE

To return to Standard Mode

Press together and opener

will beep ONCE

S T E P T H R E E

Switch power on

BLUE LED will flash

& gear LED lit

S T E P F O U R

To move the door to the

halfway point.

Proceed to Setting

Close Limit position.

If installing on a door with a bad wave action,

lengthening the arm will assist in reducing this

effect.

tip

Содержание SYNCRO ATS-3V3






























Результаты поиска

Содержание SYNCRO ATS-3V3

Отзывы:

Похожие инструкции для SYNCRO ATS-3V3

Бренды по названию

Популярные бренды

Automatic Technology SYNCRO ATS-3V3, Руководство по установке

Результаты поиска

Содержание SYNCRO ATS-3V3

Отзывы:

Похожие инструкции для SYNCRO ATS-3V3

Бренды по названию

Популярные бренды