background image

2

IMPORTANT SAFETY INSTRUCTIONS

Automatic Technology Australia Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all conditions or warranties, statutory
or otherwise which may be implied by laws as conditions or warranties of purchase of an Automatic Technology Australia Pty Ltd Garage Door Opener.
Automatic Technology Australia Pty Ltd hereby further expressly excludes all or any liability for any injury, damage, cost, expense or claim
whatsoever suffered by any person as a result whether directly or indirectly from failure to install the Automatic Technology Australia Garage Door Opener
in accordance with these installation instructions.

For 

ADDITIONAL

SAFETY

protection we

STRONGLY

recommend the fitting of a Photo Electric

Beam. In most countries Photo Electric Beams are
mandatory on all garage doors fitted with automatic
openers. For a small additional outlay ATA recommends
that Photo Electric Beams be installed with the 
automatic opener ensuring additional safety and peace
of mind.

DO NOT

operate the garage door opener unless the

garage door is in full view and free from objects such as
cars and children/persons. 

SERIOUS PERSONAL

INJURY

and/or property damage can result from failure

to follow this warning. 

DO NOT

operate the garage door opener when

children/persons are near the door. Children must be
supervised near the garage door at all times when the
door opener is in use. 

SERIOUS PERSONAL

INJURY

and/or property damage can result from failure

to follow this warning.

DO NOT

allow children to operate the garage door

opener. 

SERIOUS PERSONAL INJUR

Y and/or

property damage can result from failure to follow this
warning.

Regularly check to make sure that the 

SAFETY

OBSTRUCTION FORCE

is working correctly, and is

TESTED

(by placing a 40mm high object on the floor)

and set as per the installation instruction manual. Failure
to follow the manual may result in 

SERIOUS 

PERSONAL INJURY

and/or property damage. This

test must be repeated at regular intervals and the
necessary adjustments made as required.

DO NOT

disengage the door opener to manual

operation with children/persons or any other objects
including motor vehicles within the doorway.

Install the wall switch or wall mounted transmitter in a

LOCATION/POSITION

where it is out of reach of

children and the garage door is visible.

The door opener is not intended for use by young 
children or infirm persons without adequate supervision.
Young children should be supervised to ensure that they
do not play with the equipment.

Keep hands and loose clothing 

CLEAR

of the garage

door and opener at all times.

Warning - It is vital for the safety of persons to follow all instructions. Failure to comply

with the following Safety Rules may result in serious personal injury and/or property damage.

The unit should be installed so that it is protected from
the elements. It should not be exposed to water or rain.
It is not to be immersed in water or sprayed directly by
a hose or other water carrying device.

The garage door must be 

WELL BALANCED

.

Sticking or binding doors must be repaired by a
qualified garage door installer prior to installation of the
opener .

Frequently examine the installation, in particular
cables, springs and mountings. 

DO NOT

attempt to

repair the door yourself as hardware is under extreme
tension and can cause 

SERIOUS PERSONAL

INJURY

and/or property damage.

REMOVE OR DISABLE

all garage doors locks and

mechanisms prior to installation of the opener.

Connect the garage door opener to a properly

EARTHED

general purpose 240V mains power outlet

installed by a qualified electrical contractor.

DISCONNECT THE POWER CORD

from mains

power before making any repairs or removing covers.
Only 

EXPERIENCED

service personnel should

remove covers from the garage door opener.

When using auto close mode, a 

PHOTO ELECTRIC

BEAM

must be fitted correctly and tested for operation

at regular intervals. 

EXTREME CAUTION

is 

recommended when using auto close mode. 

ALL

SAFETY RULES 

must be followed.

In order for the garage door opener to 

SENSE 

an object

obstructing the door way, some 

FORCE

must be 

exerted on the object. As a result the object, door and/or
person may suffer 

DAMAGE or INJURY

.

If the power supply cord is damaged, it 

MUST

be

replaced by an ATA service agent or suitably qualified
person.

Make sure that the door is fully open before driving in
or out of the garage.

Make sure the door is fully closed before leaving the
driveway.

Содержание GDO-2 SecuraLife





















Отзывы: