Automatic Products SNACKSHOP 111 Series, Инструкция по эксплуатации

Страница: 17 / 61

components
13
HAND. DAMAGE TO THE MOTOR WILL RESULT. It is also
important to check polarity before applying current to the motor.
Two diodes and a capacitor are used to prevent circuit feedback
and may have to be checked when trouble shooting motor prob-
lems.
11. LIGHTING SYSTEM:
There is only one fluorescent lamp in the Snackshop 111-112.
The lamp is located on the top inside of the door which lights up
the main product area.The starter is located on the hinge side of
the lamp. The ballast and line filter is located on the top front left
shelf support. (page 21, item 16)
12. MAIN PRODUCT SHELVES:
There are five or six main product shelves per machine. Each
containing either four or eight selections. Each selection has its
own motor mounted to the back of the shelf. Every shelf has its
own harness and plug for connecting to the remainder of the cir-
cuit through the cabinet receptacle, located in the rear right of the
cabinet. The motors are the same on either type shelf. It is now
possible in the Snackshop 111-112 to exchange a five selection
shelf with a ten selection shelf or visa versa. You also have the
capability to gain 1/2 inch either up or down on any shelf. To do
this the shelf should be removed and the cabinet back harness
receptacle lowered or raised with the right & left shelf tracks.
NOTE: When exchanging the shelves, you will not need any
parts, but you will have to reprogram the machines for prices and
selections.
REMOVAL OF PRODUCT SHELF:
A. Lift up and push the lock levers toward the back of cabinet.
See figure 1, page 6.
B. Pull the shelf to its loading position.
C. Grasp shelf in front and rear center. Lift front of shelf up
above horizontal and pull shelf forward while lifting.
D. To install shelf, reverse above procedure.
13. DELIVERY BIN:
This is located below the display window on the door and is
mechanically operated. The linkage on the outside end of the
delivery bin may require occasional lubrication. Should the door
become difficult to operate, place a small amount of grease on
the arm tracks.
REMOVAL OF DELIVERY BIN:
A. Remove the screws from the underside of the delivery bin .
These screws fasten into the lower door brace and remove
the two screws and brackets at the top of the delivery bin.
B. Grasp delivery bin on both sides and lift up and pull back.
Should bin be tight, rock it by lifting on one end, then the
other.
REPLACEMENT OF DELIVERY BIN:
A. Locate lip on front edge of delivery bin over lower edge of
opening in door and behind trim. Press down along lip to
make sure it is fully engaged between door and trim.
B. Install the four screws and two brackets, to secure bin to
door.
14. REMOVAL OF GUM AND MINT MOTOR AND/OR EJECTORS:
Disconnect the two wires going to the motor and remove the four
screws holding it to the shelf. The components attached to the
front base can also be replaced. These consist of the gum and
mint shelf front (Price tabs and selection), gum and mint shelf
front base, gum and mint display front stop (plastic) and the gum
and mint ejector.
NOTE: Before replacing the gum and mint motor it would be help-
ful to tap the motor first with the screws. Assemble the four com-
ponents together and mount them to the motor making sure that
the head crank of the motor is inserted into the ejector. Replace
the four screws and test vend that selection for proper operation.
15. REMOVAL OF GUM AND MINT SHELF:
Below the gum and mint shelf remove the two screws holding the
gum and mint receptacle harness bracket (page 19, item 19).
Loosen the other two screws on each end of the gum and mint
pusher stop strap (page 31, item 20) and disengage it from the
cabinet. Grasp the shelf and pull the shelf straight out. With the
shelf out you can replace the gum and mint pusher (page 31,
item 31) by removing the screw (page 31, item 21).
Reverse the procedure to replace the shelf. Pay special attention
when you put the gum and mint pusher stop strap back on that all
the gum and mint pushers have spring tension and are behind
the strap.
16. CHILLED AIR MACHINE
When placing a chilled machine at a location Caution should be
taken to keep adequate clearance in the rear and front bottom
screens for proper circulation. The front vent screen assembly
(page 38, item 25) should be removed and cleaned periodically
for proper operation of the refrigeration system.
NOTE:The cold control setting (page 39, item 15) should be set
on the #4 position.
17. REMOVAL OF COOLING UNIT:
Replacing a cooling unit can be done by removing the two screws
from the Air Duct Support Bracket (page 37, item 3).Then, lift the
air duct up and out of the cooling unit.Remove the two screws in
the bottom of the cooling pan located to the right and next to the
blower (page 39, item 23). The cooling unit can now be pulled
straight out from the angle guides. Reverse the procedure to put
the cooling unit back in the machine.
FIGURE 10