Original Language Version
Parts support is available for this product. Please email [email protected]
4.2.6.
Plug into the mains supply, using a suitably rated heavy duty extension cord.
4.2.7.
Short Circuit/Reverse Polarity Protection
If the charger leads are wrongly connected the POWER ON light will flash, see fig.2.
4.2.8.
The POWER ON indicator will turn off.
4.2.9.
If the battery voltage is more than 7.5V, the charger will charge the batteries according to 12V mode, the 12V LED LIGHT will turn RED.
If the battery voltage is less than 7.5V, the charger will charge the batteries according to 6V mode, the 6V LED LIGHT will turn RED,
see fig.2.
4.2.10.
The charger begins charging with 0.8A low current to recover the batteries automatically if the batteries are not full.
4.2.11.
LED LIGHTS:
When the red light is on it indicates that the battery is correctly connected and the charger is charging it. The charger will deliver its full
rated current until this light turns from red to green (charged).
When the battery is fully charged, the LED will turn to green and the
charger will switch to a storage/maintenance charge mode, see fig.2.
The charger will automatically monitor and maintain the battery with 0.8A
charging current.
4.2.12.
When you are ready to use your vehicle, unplug from the mains supply,
followed by unplugging your battery terminal lead from the charger.
4.2.13.
The battery lead with terminals may be left attached to the battery.
Use care to safely stow the battery lead away from heat sources, sharp
edges and avoid pinching or crushing. The battery lead with alligator clips
should be removed before installing or using the battery.
IMPORTANT
-- If the battery is totally dead (below 4 volts) the Bank
charger will not start. This is due to its internal safety circuit. The
charger safety circuit must sense more than 4 volts before it will allow
the charger to turn on. If the battery voltage is below 4 volts, the
charger will not operate and the lights will not turn on. Have the
battery checked by a dealer if the battery voltage is very low.
Most 12 volt lead acid batteries are likely to be defective if their voltage
is below 9 volts
5. MAINTENANCE
5.1.
Cleaning and user maintenance should be carried out by competent persons.
5.2.
After use and before performing maintenance, unplug and disconnect the battery charger.
5.3.
Use a dry cloth to wipe all battery corrosion and other dirt or oil from the battery connectors, cords, and the charger case.
5.4.
Ensure that all of the charger components are in place and in good working condition, for example, the plastic boots on the battery
clips.
5.5.
Servicing does not require opening the unit, as there are no serviceable parts.
5.6.
All other servicing should be performed by qualified service personnel.
5.7.
If the mains cable is damaged, do not use until repaired.
5.8.
Store the charger unplugged, in an upright position. The cord will still conduct electricity until it is unplugged from the mains.
5.9.
Store inside, in a cool, dry place.
DO NOT
store the connectors clipped together, on or around metal, or clipped to cables. If the charger is moved around the shop or
transported to another location, take care to avoid/prevent damage to the cables, connectors and charger. Failure to do so could result
in personal injury or property damage
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note
: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important
: No Liability is accepted for incorrect use of this product.
Warranty
: Guarantee is 12 months from purchase date, proof of which is required for any claim.
AUTOGEN Technology Co., Ltd
27F Richmond Comm Bldg, 109 Argyle St
Mongkok, Hong Kong
http: //www.autogen.tech
fig.2