Auto Meter BVA-350 Скачать руководство пользователя страница 26

Страница: 26 / 28

ABOUT

From the main menu scroll down to the last selection.

Note: The down arrow

is no longer displayed.

ABOUT is the last menu

item. The up arrow

indicates previous menu

selections.

Press (Y Enter) and the

version will be displayed.

VOLT METER

SETUP

DOWNLOAD

>ABOUT

BVA-350

VERSION 2.0

DATE 07/15/2003

ERROR:

TURN OFF ENGINE

AND ACCESSORIES

‘Y’ TO CONTINUE

ERROR:

ELECT. SHORT OR

ACCESSORY DRAW

‘Y’ TO CONTINUE

ERROR:

LARGE LEADS

NOT CONNECTED

‘Y’ TO CONTINUE

ERROR:

BAD CONNECTION

ON LARGE LEADS

‘Y’ TO CONTINUE

ERROR:

SMALL LEADS

REVERSED

‘Y’ TO CONTINUE

ERROR:

SMALL LEADS

NOT CONNECTED

‘Y’ TO CONTINUE

ERROR:

CHECK LARGE

RED LEAD

‘Y’ TO CONTINUE

ERROR:

CHECK LARGE

BLACK LEAD

‘Y’ TO CONTINUE

One of the following may appear during any drop test sequence. Correct

the situation before continuing.

System noise indicates some device

is turned on. Correct by turning

vehicle loads off before continuing.

Check Tester connections and

make sure vehicle loads are off.

VOLTAGE DROP TEST ERROR MESSAGES

Содержание BVA-350





























Результаты поиска

Содержание BVA-350

Отзывы:

Похожие инструкции для BVA-350

Бренды по названию

Популярные бренды

Auto Meter BVA-350, Руководство оператора

Результаты поиска

Содержание BVA-350

Отзывы:

Похожие инструкции для BVA-350

Бренды по названию

Популярные бренды