Autel Robotics Dragonfish Pro Скачать руководство пользователя | Manualshive

Страница: 28 / 51

background image

28

may intensively interfere with satellite signal receiving, to reduce influence of multi-path
effect.



The base station must not be moved while the aircraft is in operation, otherwise the aircraft
may be disconnected, and unexpected loss may occur.

3.4 Aircraft preparation

3.4.1 Assemble aircraft

1. Install left and right wings

2. Install tail wing

3. Install wingtip propeller



Confirm that the aircraft has been turned off.



Select the propeller matched for each motor.



Forcibly press down the propeller and rotate it along the locking direction till it is installed
firmly.

Warning



Before installing or disassembling the propeller, please turn off the aircraft power switch .

Important

Align and buckle

Align and buckle

Align and buckle

«
...
26
27
28
29
30
...
»

Содержание Dragonfish Pro




















































Отзывы:

Нет отзывов

Похожие инструкции для Dragonfish Pro

Бренд: Xantrex Страницы: 4

Бренд: Easee Страницы: 12

Бренд: P-Squared Страницы: 2

Бренд: Fullwat Страницы: 8

Бренд: Jamara Страницы: 12

Smart Station S

Бренд: ALIGATOR Страницы: 28

Бренд: Hama Страницы: 38

Charger Station

Бренд: OPTI-UPS Страницы: 1

Бренд: HardWire Страницы: 18

Бренд: Hitachi Koki Страницы: 34

Бренд: CDN Страницы: 152

Бренд: Competition Electronics Страницы: 2

Бренд: BPE Страницы: 10

CONGA HOME 2000

Бренд: cecotec Страницы: 16

Бренд: LAUT Страницы: 10

Бренд: Lava Страницы: 2

Бренд: NGS Страницы: 12

Бренд: HEINE Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды