Austlift 915210 Скачать руководство пользователя

Страница: 2 / 23

ALC SIM 915210/

915220/

915230_19

SER

VICE MANU

AL (V

OL:3)

www.austlift.com.au

WIRE ROPE INERTIA REEL BLO

915210/

915220/

915230

SERVICE MANUAL (VOLUME 3) IS FOR:

Plastic Casing (Wire Rope Retractable Fall Arrester)

Retractable Fall Arrester Block

Product Code. 915210. 915220, 915230

STATUTORY CONDITIONS

1. This Service Manual contains step wise illustrations for the servicing of

AUSTLIFT Retractable Fall Arrest Block.

2. This Service Manual shall be in the custody of only a competent authorized

service personnel, duly endorsed by AUSTLIFT.

3. This Service Manual is meant only to be a handbook for ready reckoning of

the trained service provider for AUSTLIFT Retractable Fall Arrester Block.

4. Once the block has been opened up for servicing by the authorized service

personnel, AUSTLIFT shall not be responsible for any damages/ mishaps
whatsoever.

It shall be the duty of the service provider only to respond, to

such a situation.

5. It is extremely important to paste back the original label on to the block

casing after completion of the servicing.

6. Please do not forget to complete the service check card provided along

the block. This will give easy reference for future use of the block.

Содержание 915210
























Результаты поиска

Содержание 915210

Отзывы:

Похожие инструкции для 915210

Бренды по названию

Популярные бренды

Austlift 915210, Руководство по обслуживанию

Результаты поиска

Содержание 915210

Отзывы:

Похожие инструкции для 915210

Бренды по названию

Популярные бренды