Austlift 915210 Скачать руководство пользователя | Manualshive

Страница: 11 / 23

background image

11

ALC SIM 915210/

915220/

915230_19

SER

VICE MANU

AL (V

OL:3)

1300 100 120

WIRE ROPE INERTIA REEL BLO

CK

915210/

915220/

915230

STEP 15

STEP 16

Pull up the Brake plate and the Friction Plate. Immediately replace the
Friction Plate with a new one.
Also, remove the al. shim washer by removing 4 Nos. of CSK screws

Remove the wire from the drum and check the entire length for any
damages or abrasion marks. In case of any doubt about the condition of wire
rope, replace it with a new one. It is not necessary to replace the wire rope
assembly every time you service a block. Now assemble it backwards doing
the opposite of Step 15, 14 and Step 13, i.e putting back New Aluminium
shim washer the New Friction Plate, then the Brake Plate followed by the
New Pressure Washer and then the Chuck Nut.

Brake Plate

Brake Plate

Friction
Plate

Al. shim

«
...
9
10
11
12
13
...
»

Содержание 915210
























Отзывы:

Нет отзывов

Похожие инструкции для 915210

Бренд: Stihl Страницы: 112

Бренд: Toku Страницы: 37

Бренд: Performance Tool Страницы: 2

Бренд: Rugby Страницы: 20

Бренд: Hitachi Страницы: 44

Бренд: Grizzly Страницы: 12

Бренд: MW TOOLS Страницы: 35

Classic Power Drive 250HG

Бренд: RGC Страницы: 23

Бренд: Pelsue Страницы: 32

YaleERGO 360 UT

Бренд: Columbus McKinnon Страницы: 8

Бренд: Columbus McKinnon Страницы: 16

Бренд: Columbus McKinnon Страницы: 28

Бренд: Columbus McKinnon Страницы: 36

Бренд: Columbus McKinnon Страницы: 64

Бренд: Austlift Страницы: 26

Бренд: Austlift Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды