2
1
3
4
5
DO NOT REMOVE
1
3
2
4
50"
Installation
Package Contents
Video Output Via SDM (Optional)
Adjusting Directions
Keypad
Remote Control
Installation on a Flat Wall
(Minimum Distance: 40mm)
Wall Mounting
For proper installation
it is strongly recommended to use a trained,
qualified technician
.
The back of the display is equipped with four screw-holes with dimensions of
200 x 100mm (for 32”), VESA mount 200 x 200mm (for 43” and 50”), or VESA
mount 300 x 300 mm (for 55”). Firmly secure a wall mount onto the display
using four M6 screws (maximum length: 20mm, maximum torque: 16 kgf-cm).
When installing the display on a wall face, there has to be
at least 40mm of space between the display and the wall
for ventilation purposes.
The display must be installed in an environment with
proper ventilation to prevent it from overheating. Do not
block the ventilation holes on the top, left, and right sides
while keeping the display away from any heat source.
Controlling The Display
Remote Control and
AAA Batteries
Power Cord (Japan)
(By regional request)
SDM video output signal type based on SDM
model (for Set 1).
Remove screw 1, 2, 3, and 4 to remove SDM-L.
Remove screw 3 and 4 to remove SDM-S.
Refer to the figure on the right to use an SDM
to broadcast on 2 displays (Set 1, Set 2) or 3
displays (Set 1, Set 2, Set 3).
When using an SDM, configure the settings as
indicated below:
1) OSD Menu >
Setup
>
SDM/DP Power
>
Keep
2) OSD Menu >
Setup
>
RS232 Switch
>
SDM
Horizontal (Landscape)
Vertical (Portrait)
NOTE:
To prevent glare when used in a
location with strong sunlight, it is recommended
to add a cover over the display.
Item
Description
3
DOWN
Moves the selection in the OSD menu left/down.
UP
Moves the selection in the OSD menu right/up.
4
2
MENU
!
Displays the On Screen Display (OSD) menu.
!
Selects an item in the OSD menu.
5
EXIT
Exits the current menu when the OSD menu is on.
POWER
Turns the power on/off.
1
NOTE:
This button does not work when the
power switch is off.
1
2
3
4
6
7
8
Button
Description
7
SOURCE
Switches the video input
source. Use the [
!
] or [
"
]
buttons to directly select
[D-SUB], [DVI], [HDMI],
[SDM/DP].
1
POWER
Switches the power on/off.
When the power indicator
is not lit, no controls will
work.
2
MENU
Displays the OSD menu.
4
EXIT
Exits the current menu.
5
MUTE
Silences the audio from the
display.
6
ENTER
Accepts the settings made
in the OSD menu.
8
VOL
Adjusts the display’s volume
([+] to increase, [-] to
decrease).
NOTE:
!
Be careful to avoid tipping the display over when attaching
accessories.
!"
Periodically check for loose screws, gaps, distortions, or other
problems that may occur with the mounting apparatus. If a
problem is detected, please refer to qualified personnel for service.
!" #$%&'()'*"+,$+-".,$"/0&1.21%"'0+(.201"30)"42%14"03"5(/(%$"0
r
weakness that may occur over time.
Power Cord
(USA/Taiwan)
(By regional request)
Display
3
Moves the selection in the
OSD menu.
[
!
] / [
"
] /
[
#
] / [
$
]
90°
40
mm
Set 1
Set 2
(Signal Out)
Set 3
(if the SDM has a
video I/O output)
NOTE:
!
Please follow the normal shutdown procedures (Shut Down
SDM OS > Turn AC Off).
!
Turn the AC power off first before installing or removing an
SDM.
!
Signal out port is available only when an SDM is installed. To
control the connected displays via the RS232 port of the SDM,
set OSD menu >
Setup
>
RS232 Switch
>
SDM
.
NOTE:
The user manual can be downloaded from
https://pid.auo.com
SDM module Installation
Power Cord (Europe/Korea)
(By regional request)
32”
43”
50”
55”
32"/43"/55"
200.00mm
100.00
mm
200.00mm
200.00mm
200.00mm
200.00mm
300.00mm
300.00mm
2
1
3
4
5
5
49.55S1S.003
