Audison bit One HD Virtuoso Скачать руководство пользователя страница 6

Страница: 6 / 90

USER'S MANUAL

PRE IN low-level MASTER inputs

(see section 5.4.1)

Ch1 - Ch2 - Ch3 - Ch4 - Ch5 - Ch6

To connect RCA cables coming from the main analog signal source.

If these inputs are used, the MASTER SPEAKER IN inputs can not be used.

AUX auxiliary low-level STEREO inputs

(see section 5.4.2)

To connect the RCA cables coming from additional analog signal sources.

OPTICAL IN digital inputs

(see section 5.6)

Bit One HD

accepts input PCM signals up to 192 kHz / 24 bit sampling frequency rate. So DOLBY DIGITAL

(AC3) multi-channel signals coming from audio/video sources (such as the audio of a film in DVD) or DTS

can not be reproduced. These inputs can be selected using the external DRC control or activated using the

terminals

(see section. 4.3.4)

OPTICAL 1.

Connect an optical fiber cable with TOSLINK connector

OPTICAL 2.

Connect an optical fiber cable with TOSLINK connector

Remark:

when performing the installation of fiber optic cables, the minimum bending radius should be 40 mm.

A bending with higher radius value may cause the cable to break and the consequent disruption of the digital

signal.

Содержание bit One HD Virtuoso



























































































Результаты поиска

Содержание bit One HD Virtuoso

Отзывы:

Audison bit One HD Virtuoso, Руководство пользователя, Страница: 6 / 90

Результаты поиска

Содержание bit One HD Virtuoso

Отзывы: