Audipack FS-QR120 E Скачать руководство пользователя | Manualshive

Страница: 5 / 11

background image

6.

Flat panel heavier than 85 Kg must use the VESA 400 of 600 mounting pattern of the
system. When the screen is equipped with an equal mounting pattern on the back, please
contact Audipack for a fitting interface bracket.

VESA 400

VESA 600

L&S5

Applicable loads:
VESA 400 max. load 120 Kg
VESA 600 max. load 120 Kg
L&S5 max. load 85 Kg (with UFPRO)

Flat panel installation with VESA interface and cams.

When the flat panel is equipped with a VESA interface according the example, the screen
can be installed with the cams inserted directly in the back.
Choose one of the below (optional) cams to insert in the back.

M6

part no. 392618

M8

part no. 392318

M10

part no. 390618

«
...
3
4
5
6
7
...
»

Содержание FS-QR120 E












Отзывы:

Нет отзывов

Похожие инструкции для FS-QR120 E

Бренд: Sealey Страницы: 2

Бренд: Wen Страницы: 16

Бренд: K&M Страницы: 4

Бренд: Alula Страницы: 2

Бренд: Park Tool Страницы: 4

Бренд: CHIEF Страницы: 12

Бренд: HAGOR Страницы: 14

Бренд: Cavus Страницы: 4

Бренд: OE electrics Страницы: 2

Бренд: Elipson Страницы: 4

Бренд: Sanus Страницы: 6

Бренд: Renkforce Страницы: 4

Бренд: peerless-AV Страницы: 20

Бренд: Ovation Страницы: 3

Бренд: Insignia Страницы: 14

Бренд: Vivotek Страницы: 2

Бренд: Vivotek Страницы: 8

Бренд: Crestron Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды