Audiovox PRO-9649a Скачать руководство пользователя страница 7

128-6614

7 of 10

Page 7

(As per the example, press and release 5 times to set the tenths digit to 5)

6. Within 10 seconds of the last press of the pushbutton, turn the ignition switch off then on.
7. Within 10 seconds, begin to press and release the push button switch to set the units

digit.
(As per the example, press and release 2 times to set the units digit to 2).

8. Turn the ignition switch to the off position.  Immediately observe the LED flash pattern.

You will note the LED flashing five times, pause, and then flash two times, pause.  This
pattern will be repeated three times indicating the new code (52) has been accepted and
stored in memory.

NOTE:

If after step 8, the LED flashes a code other than what was just entered, this
indicates that the code has not been changed.  You will have to repeat steps 1
through 7 above being certain to note the following:

Acceptable digits 10ths or units are 1 through 9.  The unit will not recognize a 0 (Zero), or no
digit entered in any place, units or tenths.

NOTE:

If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then
5 seconds during any of the above steps, the unit will revert back to the last
successfully stored code.

MANUALLY OVERRIDING YOUR SYSTEM:
USING THE CUSTOM CODE OVERRIDE

Assuming the override code programmed has not been changed, and the default override
code of 11 is in the system's memory.

1) Enter the vehicle and turn the ignition switch to the on position.

Note:

 The siren will sound.

2) Within 5 seconds, press and release the pushbutton switch 1 time.
3) Within 5 seconds, turn the ignition switch off then on.
4) Within 5 seconds, press and release the pushbutton switch 1 time.
5) Turn the ignition switch off then on and start the vehicle.

NOTE:

 If you have changed the programmed override code then substitute your      new code

tenths for step 2 above, and units for step 5 above.

ELIMINATING THE NORMAL ARM / DISARM CHIRPS

As explained earlier in the manual, you can eliminate the chirps selectively any time you arm
or disarm the system simply by holding the ARM / DISARM button for two seconds. If you find
the normal arming and disarming chirps annoying, they can be turned off permanently,
eliminating the need to hold the ARM / DISARM button for two seconds. To do this,

1. Turn the ignition key on then off.
2. Within 10 seconds, press and release the valet push button switch three times.
3. If the chirps were on before you started, then you will hear 2 chirps indicating they have

been turned off.

If the chirps were off before you started, then you will hear one chirp indicating they have
been turned on.

NOTE:

Whenever the chirps are by-passed, the 4 chirp intrusion indicator and 3 chirp

Содержание PRO-9649a











Отзывы: