Audiovox ca 6552 Скачать руководство пользователя | Manualshive

Страница: 13 / 38

background image

13

ca6552/6552sst. 2011 Audiovox Electronics Corporation. All rights reserved.

7

BROWN/RED

BRAKE INPUT ( + )

Locate the vehicle’s brake light wire at the brake pedal mounted switch. This
connection is required for remote start.

Verification: This wire registers positive voltage when the brake pedal is
pressed.

Connect the BROWN/RED wire to the vehicle’s brake light wire.

6

BLACK/WHITE

NEUTRAL SAFETY INPUT ( - )

Locate the vehicle’s neutral safety circuit.

Verification: This wire registers ( - ) voltage when the vehicle’s gear
selector is in park or neutral.

Connect the BLACK/WHITE neutral safety input wire to the neutral safety wire of
the vehicle or an optional toggle switch. The remote start feature will not operate
unless this input is supplied with a ground source.

8

PURPLE/WHITE

TACH INPUT

Locate the vehicle’s ignition coil or fuel injector in the engine compartment.

Verification: Test using the following procedure:

1.

Set voltmeter to AC VOLTS.

2.

Attach positive lead of a volt meter to a constant 12 volt source.

3.

Attach negative lead of a volt meter to the wire to be tested.

4.

Start the engine.

5.

Have someone press on the gas pedal slightly as you monitor the meter. If
connected to the correct wire, the voltage reading will increase as the
engine’s RPM increases.

Connect the PURPLE/WHITE wire to the negative side of the vehicle ignition coil or
fuel injector.

«
...
11
12
13
14
15
...
»

Содержание ca 6552







































Отзывы:

Нет отзывов

Похожие инструкции для ca 6552

Бренд: x-sense Страницы: 25

Бренд: LST Страницы: 1

Бренд: REIZEN Страницы: 7

Бренд: Galeria Selection Страницы: 10

Бренд: Dynatech Страницы: 9

Бренд: Kidde Страницы: 11

Ampac TITANUS PRO-SENS

Бренд: Halma Страницы: 197

Бренд: Siemens Страницы: 5

Бренд: ND tackle Страницы: 7

vesda LaserFOCUS VLF-500

Бренд: Xtralis Страницы: 61

Бренд: System Sensor Страницы: 4

Бренд: La Crosse Страницы: 10

Бренд: Code Alarm Страницы: 24

Бренд: La Crosse Technology Страницы: 5

RADIO CONTROLLED PROJECTION CLOCK WITH DIGITAL...

Бренд: La Crosse Technology Страницы: 7

Бренд: Landmann Страницы: 69

Бренд: Mega Страницы: 8

Бренд: Eaton Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды