AMP210VS
OWNER’S MANUAL
13970 SW 72nd Ave, Portland, OR 97203 • 503.914.4688 • www.audiosource.net
4
APPLICATIONS
STEREO SETUP
In this configuration, the mode switch is set to “Stereo”. Connect the line out jacks
from a stereo pre-amplifier or source to the MAIN input jacks of your AMP210VS.
Next connect your speakers to the terminals marked “Speaker A” observing
proper polarity. Select the “A” speakers using the front panel zone selection
buttons. Connect a second (optional) pair of speakers to the terminals marked
“Speaker B”. If you are connecting 4 speakers to the AMP210VS they must be
8 ohm speakers only. Press A and B together to use both zones.
SETUP FOR MULTIPLE SOURCE
In the multiple source set up, a distributed audio system is connected to the
AMP210VS as a local zone amplifier via the MAIN inputs. Normally the distributed
audio system will be the audio source for the AMP210VS. The distributed audio is
then passed on to be used by additional zones or sub zones in the distributed
system via the MAIN outputs.
The audio output of a local source, such as an MP3 Player, CD, television,
computer, etc., is connected to the AMP210VS via the INTERRUPTING inputs, and
whenever the local source is active its signal will take priority over the
distributed audio signal present at MAIN input . However, the distributed audio signal
will still be present at the MAIN input. In this circumstance the audio output of the
local source will be heard via the AMP210VS. Once the local source is turned
off or muted, the AMP210VS will automatically switch back to the distributed audio
system as an audio source, assuming the local source remains inactive. There
is a delay of up to 6 seconds when switching from INTERRUPTING input back
(From Pre-amp or Receiver Line Out)
(From Pre-amp Line Out)
(From Local Source Line Out)
(Out to Additional Zones)
L
R
L
R
Limited Warranty
AudioSource® warrants its amplifier products against defects in materials
and workmanship for a limited period of time. For a period of two years from
date of original purchase, we will repair or replace the product, at our option,
without charge for parts and labor. Customer must pay all parts and labor
charges after the limited warranty period expires. The limited warranty period
for factory refurbished products expires after ninety (90) days from date of
original purchase.
This limited warranty applies only to purchases from authorized AudioSource®
electronics retailers. This limited warranty is extended only to the original
purchaser and is valid only to consumers in the United States.
Consumers are required to provide a copy of the original sales invoice from
an authorized AudioSource® dealer when making a claim against this limited
warranty. This limited warranty only covers failures due to defects in materials
or workmanship that occur during normal use. It does not cover failures
resulting from accident, misuse, abuse, neglect, mishandling, misapplication,
alteration, faulty installation, modification, service by anyone other than
AudioSource®, or damage that is attributable to Acts of God. It does not
cover costs of transportation to AudioSource® or damage in transit. The
customer should return his defective product, freight prepaid and insured, to
AudioSource® only after receiving a Return Authorization.
This warranty will become void if the serial number identification has been
wholly or partially removed, altered or erased. Repair or replacement under
the terms of this warranty does not extend the terms of this warranty. Should
a product prove to be defective in workmanship or material, the consumer’s
sole remedies will be repair or replacement as provided under the terms
of this warranty. Under no circumstances shall AudioSource® be liable for
loss or damage, direct, consequential or incidental, arising out of the use of
or inability to use the product. There are no express warranties other than
described above.
to MAIN inputs.
Mains Power Inlet & Fuse Holder
Accepts IEC type line cord. Afuse located in the integrated holder provides safety
protection from fault conditions: replace fuse with one of same type and rating only.
17.
Mains Voltage Selector
Voltage selection switch is preset to 115V (USA). For use in areas which require
230V contact your dealer. Fuse must be of type and rating marked on amplifier for
use at local mains voltage.
18.
