AudioCodes Media Pack MP-11x Скачать руководство пользователя страница 589

Страница: 589 / 650

Version 6.6

589

MP-11x & MP-124

User's Manual

44. Configuration Parameters Reference

Parameter

Description

Web: NRT Retry
Subscription Time
EMS: NRT Subscription
Retry Time

[NRTSubscribeRetryTime]

Defines the Retry period (in seconds) for Dialog subscription if a
previous request failed.

The valid value range is 10 to 7200. The default is 120.

Web/EMS: Call Forward
Ring Tone ID

[CallForwardRingToneID]

Defines the ringing tone type played when call forward notification is
accepted.

The valid value range is 1 to 5. The default is 1.

44.11.5.4

Message Waiting Indication Parameters

The message waiting indication (MWI) parameters are described in the table below.

Table

44-45: MWI Parameters

Parameter

Description

Web: Enable MWI
EMS: MWI Enable

[EnableMWI]

Enables Message Waiting Indication (MWI).



[0]

Disable (default).



[1]

Enable

Notes:



This parameter is applicable only to FXS interfaces.



The device supports only the receipt of SIP MWI NOTIFY
messages (the device doesn't generate these messages).



For more information on MWI, see 'Message Waiting
Indication' on page

287

Web/EMS: MWI Analog Lamp

[MWIAnalogLamp]

Enables the visual display of MWI.



[0]

Disable (default).



[1]

Enable = Enables visual MWI by supplying line voltage

of approximately 100 VDC to activate the phone's lamp.

Notes:



This parameter is applicable only for FXS interfaces.



This parameter can also be configured in a Tel Profile.

Web/EMS: MWI Display

[MWIDisplay]

Enables sending MWI information to the phone display.



[0]

Disable = (Default) MWI information isn't sent to display.



[1]

Enable = The device generates an MWI message

(determined by the parameter CallerIDType), which is
displayed on the MWI display.

Note:



This parameter is applicable only to FXS interfaces.



This parameter can also be configured in a Tel Profile.

Web: Subscribe to MWI
EMS: Enable MWI Subscription

[EnableMWISubscription]

Enables subscription to an MWI server.



[0]

No (default)



[1]

Yes

Notes:



To configure the MWI server address, use the MWIServerIP
parameter.



To configure whether the device subscribes per endpoint or

Содержание Media Pack MP-11x











































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Media Pack MP-11x

Отзывы:

Похожие инструкции для Media Pack MP-11x

Бренды по названию

Популярные бренды

AudioCodes Media Pack MP-11x, Руководство пользователя

Результаты поиска

Содержание Media Pack MP-11x

Отзывы:

Похожие инструкции для Media Pack MP-11x

Бренды по названию

Популярные бренды