background image

16

REF 160M Manual.indd   16

4/4/18   8:54 AM

Operation

Front Panel Button Functions

Power

Turns power of Reference 160S on or off. 

Meter Light

Adjusts meter light LED display brightness to one of four levels of brightness including “off”.

Tube Monitor

Allows checking the operation of each of the eight KT 150 output tubes (V1-V8). The LED 

associated with each output tube will illuminate when operating properly. See Auto Bias 

section under Operation for further explanation of its operation.

Ultra-Linear/Triode

Allows selecting ultra-linear (approximately 140 watts/ch.) operation –indicated by green color 

of LED above this function button, or triode (approximately 70 watts/ch.) operation –indicated 

by blue white color of the power-on LED.

Back Panel Toggle Switch Functions

Auto Shut Off/ Defeat

Allows selecting auto shut-off feature or turning off this feature (see separate Auto Shut Off 

paragraph under this Operation section for a  more detailed description of  this function).

High/Low Fan Speed

Allows adjusting fan speed to either low or high-speed setting.

Balanced/Single Ended

Select balanced switch position for balanced  input connection operation or single-ended  

switch position for single-ended input connection operation. Do not connect BAL and SE cables 

simultaneously. (See Input  Connectors paragraph under Connections section for further 

information.)

Auto Shut Off

The Reference 160S is equipped with an auto shut-off feature, designed to turn the amplifier off 

after two hours of no signal being present at the output of the amplifier.

In the event that quiet music is listened to at very low volumes, there may not be adequate 

signal for the auto shut off circuit, resulting in the amplifier turning itself off. If this is the case, 

please disengage the auto shut off feature. The auto shut off feature control switch is located 

on the back panel of the Reference 160S. 

Note: 

The auto shut off feature is not in the signal path of the amplifier and has no deleterious 

sonic effect on music playback. 

Содержание REFERENCE 160S

























Отзывы: