manualshive.com logo in svg

Audio enhancement TLD100, Руководство по эксплуатации

Поделиться
Скачать
Audio enhancement TLD100 Скачать руководство пользователя страница 34

34

Specifications

General

Power (DC IN)

24 V DC (use the specified AC adaptor (included))

Input current

160 mA  (At 4 pieces of extended sensors (EDS-07) connected)

Operating temperature range

0 °C - 40 °C {32 °F - 104 °F}

Dimensions

Sensor/receiver: ø152 mm x 76 mm (H) {ø6 inches x 3 inches (H)}
* Excluding F-type connector
Conversion box: 25.5 mm (H) x 67 mm (W) x 67 mm (D)
{1 inch (H) x 2-5/8 inches (W) x 2-5/8 inches (D)}
* Excluding screw hole

Mass

Sensor/receiver: Approx. 500 g {1.1 lbs}
Conversion box: Approx. 80 g {0.18 lbs}

Finish

Sensor/receiver: 

Infrared passing-type acrylic resin (black color)

 

 

ABS resin white color

Conversion box:  ABS resin black color

IR receiver

Reception channel  
(subcarrier frequency)

CH1: 2.3 MHz, CH2: 2.8 MHz

Reception system

T.R.F. (Tuned Radio Frequency)

Receiving sensitivity

S/N 60 dB or more (40 dBµV input, ±12.5 kHz FM @1 kHz)

Signal-to-noise ratio

70 dB or more (60 dBµV input, ±12.5 kHz FM @1 kHz)

Audio

General
 

Signal-to-noise ratio

70 dB or more (Line in to Mixing output)

 

Frequency response

50 Hz – 15 kHz (Line in to Mixing output)
100 Hz – 10 kHz (Microphone to Mixing output)

 

Total harmonic distortion

0.5 % or less @1 kHz (Line in to Mix
1.0 % or less (Microphone to Mixing output, 60 dBµV input, ± 12.5 kHz FM @1 kHz)

ing output)

LINE IN L/R

–10 dBV input impedance 10 kΩ or more Unbalanced, stereo (monaural mixing), 
ø3.5 mm (ø1/8 inches) stereo mini jack (Tip: Left, Ring: Right, Sleeve: GND)

CH1/CH2 (Microphone output)

–5 dBV Balanced, Adaptive impedance 10 kΩ or more,
ø3.5 mm (ø1/8 inches) stereo mini jack (Tip: Hot, Ring: Cold, Sleeve: GND)

MIX OUT

0 dBV Balanced, Adaptive impedance 10 kΩ or more,
ø3.5 mm (ø1/8 inches) stereo mini jack (Tip: Hot, Ring: Cold, Sleeve: GND)

Control terminal

F1 CNT, Com

Output format: open collector, make output
Electrical specifications: control voltage; 30 V, control current; 20 mA

F2 CNT, Com

F2 ACK, GND

Input format: transistor input
Electrical specifications: open voltage; 5 V DC, short-circuit current; 2 mA

PAGE MUTE, GND

RS-232C

TxD

Compliant with RS-232C, asynchronous, 9600 bps

RxD

SG

Содержание TLD100





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды