manualshive.com logo in svg

Audio enhancement TLD100, Руководство по эксплуатации

Поделиться
Скачать
Audio enhancement TLD100 Скачать руководство пользователя страница 15

15

F1 CNT, F2 CNT function

These functions are available when MTD-09 is used. When F1 or F2 signal is transmitted from the microphone, it will  
active F1 CNT or F2 CNT terminal on the receiver. Selection between F1 and F2 is made at the microphone side.
Function 1 (F1): Default setting is Open.
 

Press the function button [F] of the microphone to select the closed state of 300 ms.

Function 2 (F2): Default setting is Open.
 

Press the function button [F] of the microphone for 2 seconds or more to select the closed state.

Note:

• 

To stop the microphone from transmitting the F2 signal, it must be turned off. Then turn off the IR-Satellite Sensor/ 
Receiver (this unit) to reset it.

 

If the IR-Satellite Sensor/Receiver (this unit) is not turned off, the F2 terminal will be open (reset) 3 minutes after not  
receiving a signal from the microphone.

F1 CNT 

(Holding 

down) 

Microphone

300 ms

300 ms

300 ms

600 ms

600 ms

600 ms

300 ms

3 LEDs flash 

in blue.

F2 terminal will be closed when 

3 commands are sent within 5 

seconds after the first F2 

command. 

Commands are 

sent periodically 

from the 

microphone while 

holding down the 

function button 

[F].

F1

F2 CNT

Open

Closed

Microphone

5 s timer/ch

3 minutes timer

2 s

1 s

1 s

1 s

1 s

Last F2 command

Timer restarts. 

F2

TLD100

F2

terminal

Open

Closed

TLD100

F1

terminal

Open

Closed

TLD100

F1

terminal

F1 CNT 

(Press) 

Microphone

300 ms

3 LEDs flash 

in blue.

Default setting: 

Open

Default setting: 

Open

Default setting: 

Open

Flash!

F1

Type

Actions

Commands are sent 

periodically from the 

microphone until the 

power is turned off.

3 minutes from the 

last F2 command

1st

2nd

3rd

ON

OFF

or

Hidden

Flash!

Flash!

Flash!

Flash!

Flash!

3 LEDs 

light 

in blue.

Holding down

Содержание TLD100





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды