Audio Alto DMI 3 H Скачать руководство пользователя страница 4

 

© by www.audioalto.com  

 

SAFETY PRECAUTIONS 

 

IMPORTANT SAFEGUARDS 

 

PLEASE READ CAREFULLY ALL THE FOLLOWING IMPORTANT SAFEGUARDS THAT ARE 

APPLICABLE TO YOUR EQUIPMENT CAUTION! 

 

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE SCREWS.  

NO USER SERVICEABLE PARTS INSIDE.  

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 

 

SAFETY 

 

1)

 

Read the User’s Manual and refer to it frequently during use of this product - All the safety 
and operating instructions should be read before the product is operated.  

2)

 

Retain the User’s Manual - The safety and operating instructions should be retained for 
future reference.  

3)

 

Follow Instructions - All operating and instructions for use should be closely followed.  

4)

 

Power Sources - This product should be operated using only the type of power source 
indicated on the marking label. If you are not sure of the type of power supply in your home, 
consult your product dealer or local power company.  

5)

 

Grounding - This product is equipped with a three prong IEC connector. Always use power 
cord with adequate wire cross section and an electrical outlet that is grounded. If you do not 
know whether the outlet is grounded, consult your electrician or local power company.  

6)

 

Power Cord Protection – Power supply cords should be routed so that they are not likely to 
be walked on or pinched. Pay particular attention to cords at plugs, convenience receptacles 
and where they exit from the product. Always use power cords with adequate current ratings 
and safety certifications (UL, CE, TÜV, CSA, etc.)  

7)

 

Fuses - For continued protection against fire hazard, replace fuses with the same type and 
rating of the fuses specified. When changing fuses, completely unplug the AC cord from the 
wall outlet.  

8)

 

Vacuum Tubes - During operation the tubes get very hot. Do not touch the tubes since this 
may result in a severe burn. Allow at least 10 minutes after removing power for tubes to cool 
down before touching them.  

9)

 

Turn-off when not using - Turn off the unit as you stop actively using it. Unplug the power 
supply from the wall during a lightning storm or when the product is to be left unattended 
and unused for longer periods of time. 

 

ENVIRONMENT 

1)

 

Water and Moisture - Do not use this product near water - i.e. near a bathtub, ash bowl, 
kitchen sink or laundry tub; in a wet basement; or near a swimming pool or the like. Damp 
basements should be avoided.  

2)

 

Heat - The product should be situated away from heat sources such as radiators, heat 
registers, stoves or other appliances that produce heat. Also avoid putting the unit in the 
direct rays of the sun.  

3)

 

For indoor use only.  

 

Содержание DMI 3 H














Отзывы: