Audi 2007 TT Coupe Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 69

Audi 2007 TT Coupe Скачать руководство пользователя страница 60

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.

2.42

Transport Protection, Removing Front

and Rear Suspension Strut Protectors

Two versions of protection devices are used. (front spring ridges ,

rear blocking pieces)
– Release coil spring (for example, put vehicle on lift)

Note

♦

It is not necessary to remove the wheels.

♦

Be careful not to damage surface of coil springs.

– Remove protection devices from springs.

Note

After removing the spring clip and the spacer and lubricating the

strut tube cap, make sure that the boot in the strut bearing is in

the correct position as with the shock absorber tube.

2.43

Underbody Protection, Inspecting for

Damage

– When inspecting, observe underbody, wheel housings and

sills!

WARNING

Eliminate any malfunctions (repair procedure).

2.44

Plenum Chamber Water Drain, Check‐

ing and Cleaning

– Remove the plenum chamber cover .

Note

♦

Visually inspect plenum chamber for contaminants, for exam‐

ple, leaves.

♦

If there are contaminants, clean water drain and plenum cham‐

ber.

Remove the plenum chamber cover. Refer to ⇒ Body Exterior;

Rep. Gr. 50 ; Removal and Installation

2.45

Factory-Equipped Winter Tires

Note

♦

On vehicles that were delivered from factory with winter tires,

check for correct pressure during delivery inspection.

♦

The excessive speed warning label should be placed in driver

field of vision.

Audi TT 2007 ➤

Maintenance Procedures - Edition 08.2011

56

Rep. Gr.03 - Maintenance, Diagnosis

«
...
58
59
60
61
62
...
»

Содержание 2007 TT Coupe






































































Отзывы:

Нет отзывов