AuCom EMX4i страница 15 Скачать руководство пользователя | Manualshive

Страница: 15 / 126

background image

SYSTEM DESIGN

14

EMX4i User Manual 710-14888-00C

3.6

Physical Installation

D

D

17044.

B

C

C

B

A

Between starters

Solid surfaces

A

B

C

D

> 100 mm (3.9 inch) > 10 mm (0.4 inch) > 100 mm (3.9 inch) > 10 mm (0.4 inch)

3.7

Accessories

Expansion Cards

The EMX4i offers expansion cards for users requiring additional inputs and outputs
or advanced functionality. Each EMX4i can support a maximum of one expansion
card.

•

Smart Card

The smart card has been designed to support integration with pumping applications
and provides the following additional inputs and outputs:

•

3 x digital inputs

•

3 x 4-20 mA transducer inputs

•

1 x RTD input

•

1 x USB-B port

•

Remote keypad connector

•

Communication Expansion Cards

The EMX4i supports network communication via easy-to-install communications
expansion cards. Each communications card includes a remote keypad connector
port.
Available protocols:
DeviceNet, Ethernet/IP, Modbus RTU, Modbus TCP, Profibus, Profinet.

«
...
13
14
15
16
17
...
»

Содержание EMX4i































































































































Отзывы:

Нет отзывов

Похожие инструкции для EMX4i

Бренд: OmarLift Страницы: 14

Бренд: Federal Signal Corporation Страницы: 79

Бренд: Federal Signal Corporation Страницы: 32

Бренд: Taie Страницы: 28

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 111

Бренд: Eaton Страницы: 448

Бренд: Eaton Страницы: 57

Бренд: Bardiani Страницы: 96

Бренд: Eaton Страницы: 4

AMES 4000SS Series

Бренд: Watts Страницы: 8

Бренд: SYCLOPE electronic Страницы: 40

Бренд: Timotion Страницы: 10

Бренд: M-system Страницы: 7

Бренд: Combi Страницы: 16

RM-LUM-M320-IT/A

Бренд: Grosvenor Страницы: 2

Calc-An-Acre II

Бренд: micro-trak Страницы: 30

Ecomat100 CR1055

Бренд: IFM Страницы: 32

Бренд: Contemporary Research Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды