ATTO Technology iPBridge 2600 Скачать руководство пользователя страница 27

22

Performance issues

If the host is not getting the performance it should, 
check the following items. 

Check SCSI devices

1

Verify that the devices are running at their 
highest possible SCSI speed.
Mixing SE and LVD devices on the same SCSI 
bus forces the speed of the bus to SE, thus 
slowing faster LVD devices. The iPBridge 
cannot accelerate an already slow device. 
Refer to 

Connecting SCSI devices to SCSI 

ports

 on page i of the Appendix.

2

Verify that the proper terminator is being used. 
An SE terminator forces the SCSI bus to SE 
speeds.

Check iPBridge SCSI ports

1

Verify that the SCSI port configuration is set to 
the highest speed using the ATTO ExpressNAV 
interface or CLI. 
The iPBridge SCSI port speed, wide 
negotiation, and sync negotiation settings all 
affect the speed of the port. By default, these 
settings are set for optimal speed.

2

Verify that the SCSI devices are equally 
distributed between the SCSI ports. 

3

Optimal performance is seen when only two 
high-speed SCSI devices are connected to 
each SCSI port.

Check iPBridge Ethernet ports

1

Verify that the data ports are set to auto 
negotiate or forced to 1000 Mb/sec. 

2

Verify that the MTU size is set to optimal setting 
for the LAN/WAN environment. 
The current optimized frame size for the 
iPBridge is 9k.

3

Verify that the iPBridge Trace Log feature is 
disabled. Refer to 

TraceLog 

 on page xiv in the 

Appendix. The log tracks certain events that 
occur in the iPBridge. With this log enabled, 
performance suffers.

Check the LAN/WAN

1

Verify that the MTU size is set to optimal setting 
for the LAN/WAN environment. 
9k frame size is the current optimized frame 
size for the iPBridge. Many switch and router 
vendors do not support the larger frame size of 

9k or 16k. 

2

Verify that each associated port in the IP SAN 
is configured for 1000Mbs.
IP SAN traffic should be segmented so that it 
does not interfere with the main LAN network 
traffic.For better performance, the IP SAN 
should be on its own set of hardware.

3

Verify that packets are not being dropped along 
the LAN/WAN. Many utilities track packet 
activity and switch statistics.

Check Ethernet Host Adapter or NIC

Ethernet Storage Adapters generally outperform 
accelerated NICs and un-accelerated NICs by 
offloading most of the processing from the host.
An accelerated NIC provides some offloading, but still 
requires a host OS iSCSI driver, making the host spend 
more CPU cycles.
An un-accelerated NIC does not offload anything so 
the CPU must do much of the processing.
To check the Ethernet host adapter or NIC

1

Verify that the adapter or NIC is sent to auto-
negotiate or forced to 1000 Mbs.

2

Set the MTU size to the largest MTU size 
supported in the LAN/WAN. 

9k frame size is the current optimized frame size for 
the iPBridge. Many switch and router vendors do not 
support the larger frame size of 9k or 16k. Set the 
maximum transfer size to the most efficient size for the 
intended target(s). For many tape drives, 64k is the 
optimal setting.

Check the applications

Some applications can be configured to change 
transfer sizes. Configure the application for the 
optimal size for the particular SCSI device(s) 
connected to the iPBridge.

Check the host system

The faster the host, the faster your transfer times are. 
The work flow goes only as fast as the slowest 
connection in the host system, so transferring data 
from an IDE drive, 100Mb connection, a DLT 4000, a 
high speed RAID volume across the country, or other 
applications, slows the system no matter how fast 
everything else is in the system.

Содержание iPBridge 2600



















































Отзывы: