background image

Integrated Access Controller  – Installation manual  

All rights reserved. © AAT HOLDING S.A.

 

 

Detailed Programming Guide 

User Settings

 

To enter the programming mode

 

 *  Master code #

 

 888888 is the default factory master code

 

To exit from the programming mode

 

 *

 

Note that to undertake the following programming the master user must be logged in

 

To change the master code

 

 0  New code  #  New code #

 

The master code is any 6 digits

 

Setting the working mode:

 

Set valid 

card or PIN

 users

 

 

 

Set valid 

card and PIN

 users

 

 

 

 

 

Set valid 

card ONLY

 

 

 

3   1   2   # , Zone 1

 

3   2   2   # , Zone 2

 

Entry by 

card or PIN

(Factory default setting)

 

3   1   1   # , Zone 1

 

3   2   1   # , Zone 2

 

Entry by 

Card and PIN

 together

 

3   1   0   # , Zone 1

 

3   2   0   # , Zone 2

 

Entry by

 Card only

 

Note:

 When adding users, if the Card or PIN user has been enrolled already, you can not add it again to the 

same zone, or the device will give a bleep as error. But it is ok to enroll the same card or PIN for the zone 1 
and zone 2.

 

Card or PIN Mode - Factory default setting 

 ( 3   1   2   #  for 

Zone 1

 or 3   2   2   #  for 

Zone 2

)

 

To add 

PIN

 users

 

1   1  User ID number  #  PIN #  

Zone 1

: User ID: 1-2000

 

1   2  User ID number  #  PIN #

 

Zone 2

: User ID: 2001-2100

 

The PIN is any 4~8 digits between 0000~99999999 with 
the exception of 1234 which is reserved. Users can be 
added continuously without exiting programming mode 
as follows:

 

1   1  User ID number 1 # PIN# User ID number 2 #  
PIN #   

Zone 1

 

1   2  User ID number 1 # PIN# User ID number 2 #  
PIN #   

Zone 2

 

To delete 

PIN

 users

 

2   0   User ID number  #

 

Users can be deleted continuously without exiting pro-
gramming mode

 

To change the 

PIN

 of a PIN user

 

(This step must be done out of programming 
mode)

 

 *  User ID number #  Old PIN #  New PIN #

 

New PIN #

 

To add a 

card

 user (Method 1)

 

This is the fastest way to enter cards using ID 
number auto generation.

 

1   1  Read card  #  

Zone 1

 

1   2  Read card  #  

Zone 2

 

Cards can be added continuously without exiting pro-
gramming mode

 

To add a 

card

 user (Method 2)

 

This is the alternative way to enter cards using 
User ID Allocation. In this method a User ID is 
allocated to a card. Only one user ID can be allo-
cated to a single card.

 

1   1   User ID number  #  Read Card #  

Zone 1

 (User 

ID: 1-2000)

 

1   2  User ID number  #  Read Card #  

Zone 2

 (User 

ID: 2001-2100)

 

Содержание Kade KZ-700-U/H













Отзывы: