Atronic e-motion Скачать руководство пользователя страница 50

Страница: 50 / 59

April 2007

e-motion™ Operating Manual - B-Level STD

ACHINE

ONVERSION

PAYTABLE CONVERSION

If the machine is converted to a new paytable type,

these areas of the machine are involved.

Paytable Software

Legend Kit

Paytable Software

The paytable software EPROM, located on the

mainboard, is available in two types:

Non-Configurable

(Standard Paytable)

Configurable

(Selectable Paytable)

Non-configurable paytable software requires a RAM

reset and the replacement of the paytable EPROM in

order to convert the paytable.

Configurable paytable software allows the change of

paytable settings by means of a RAM reset.

Configurable paytables are not applicable in all

jurisdictions.

Button Panel Decals / Legend Foil Kit

A button panel conversion is necessary, if a new

paytable setting with different LINES and BET PER

LINES steps is used. In most cases a button panel

conversion can be done by changing the button decals.

Button decals are delivered as a legend foil kit that

consists of a group of button decals.

Use a gaspipe pliers with soft clamping to carefully

remove the button lens caps in order to convert the

button decals.

Note:

See manual "Software / Basic

Setup" for a detailed RAM

reset procedure.

Содержание e-motion




























































Результаты поиска

Содержание e-motion

Отзывы:

Atronic e-motion, Руководство по эксплуатации, Страница: 50 / 59

Результаты поиска

Содержание e-motion

Отзывы: