Hold time
Adjusting the duration time:
The length of time that remains
switched on after activation can be
adjusted from (10±5) seconds to (7)
minutes. Rotating the TIME knob + to
- will reduce the duration time.
Note:
Once the sensor has been
triggered any subsequent detection
will start the timed period again from
the beginning.
Min. 10 sec ± 3 sec
Max. 7 min ± 2 min
Lux operation
Adjusting the LUX control level:
The Lux control module has a
built-in sensing device (photocell) that
detects daylight and darkness.
The ( ) position denotes that the
sensor can work at day and night,
and the (3) position only work at
night. You can set to operate the
unit at the desired level by
adjusting the LUX knob.
darkness operation only
daylight sensor disabled
Setting the Controls
Warranty
Atom products are distributed in Australia by Evolt Pty Ltd ('us', 'our', or 'we'). Our contact information is
set out in the bottom right hand corner of this page.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You
are entitled to a replacement or refund for a major failure and compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a major failure.
In addition to your guarantees under the Australian Consumer Law, our goods also come with a
contractual warranty, which is described below. This warranty is additional to your rights under the
Australian Consumer Law (and any other rights or remedies you may have under a law in relation to the
products) and is not intended to modify or exclude those rights.
Subject to the terms of this contractual warranty, if your Atom products are defective, we will (at our
election) repair or replace the Atom products. Once we make this election (and take the relevant action),
we will have honored our obligations under this contractual warranty.
Our total liability under this warranty is limited to the cost of repair or replacement of the defective
product (at our election). We otherwise exclude all liability in relation to the product to the fullest extent
permitted by law (noting our comments above regarding the Australian Consumer Law and any other
rights or remedies you may have).
If you wish to claim under this warranty, you must, at your own expense, return the product or that
part of the product which you believe is defective, together with proof of original purchase, your name,
address and telephone number and a certificate of installation (or other document required by the
law for the installation of electrical products in the place in which the product was installed) to Evolt at
the address set out in the bottom right hand corner of this page within the warranty period. You bear
all costs associated with claiming under this warranty (including, but not limited to, postage costs).
Without limiting the preceding sentence, this warranty does not apply to the costs of the removal or
re-installation of the defective product.
The warranty period for this product is three years from the date of purchase. This warranty is not
transferable and is only given to the original purchaser of the product, provided the purchaser has
purchased the product from us. Proof of purchase must be provided to us with any warranty claim. We
recommend that you attach your proof of purchase to your product manual.
This warranty does not apply to consumable items within your product (including, but not limited
to, lamps or batteries). This warranty does not apply to products that have been improperly stored,
installed, or used. This warranty does not apply to products that have not been maintained in
accordance with the instructions contained within this product manual.
This warranty does not apply to loss or damage caused by wear and tear, misuse, incorrect installation
or operation, failure to clean and maintain, incorrect voltage or non-authorised electrical connections,
adverse external conditions (such as power surges and dips, acts of God, exposure to heat, corrosion,
insect or vermin infestation), use of non-authorised or defective parts or globes, or to items that have
been repaired than by a person other than us or a repairer approved by us.
Atom
is a registered brand of Evolt PTY Limited.
For further information please call Evolt’s head office on 1300 4EVOLT (438 658).
Evolt PTY Limited PO BOX 271 KINGSGROVE NSW 1480
ABN 83 112 123 529
Due to changes in industry standards and Evolt’s policy of continual product development, product
specifications are subject to change without notice.
Images are for illustrative purposes only.
For more information please visit our website www.evolt.com.au
1394905_V1.0
Trouble Shooting and User Hints
1. Put the Lux control knob to light (*) position, turn the wall switch on
and wait half a minute for the control circuit to stabilize. At this stage
ensure that the TIME control knob is set at minimum duration.
The output will now switch on and remain on for about 10 seconds
2. Have another person move across the center of the area to be
scanned until the unit sensors the presence of the moving person,
causing the output to switch on.
3. Adjust time control to required setting.
4. To set the light level at which the lights will automatically switch “ON”
at night, turn the LUX control knob from ( * ) position to lowest lux
position. If the lamps are required to switch on earlier, e. g. Dusk,
wait for the desired light level, then slowly turn the LUX control knob
towards daylight while someone walks across the center of the area
to be detected. When the output on, release the LUX control knob.
You may need to make further adjustments to achieve your ideal
light level setting.
Problem
Possible Cause
Suggested Remedy
OUTPUT DOES
NOT SWITCH
ON WHEN
THERE IS
MOVEMENT
IN THE
DETECTION
AREA.
•
No mains voltage
•
Nearby lighting is too bright
•
Controls set incorrectly
•
Check all connections, and fuses
switches
•
Reposition sensor or relocate the unit
•
Reposition sensor controls
OUTPUT
SWITCHES
ON FOR NO
APPARENT
REASON
(FALSE
TRIGGER)
•
Heat sources such as
air-con, vents, heater
flues, barbecues, other
outside lighting, moving
cars are activating sensor
•
Interference from ON/
OFF switching of electric
fans or lights on the same
circuit as your output (this
problem does not always
occur but a faulty switch
or noisy fluorescent light
may cause the output to
switch on)
•
Reflection from swimming
pool, or reflective surface
•
Reposition sensor
•
Should the false triggering become
troublesome, consider:
a) Replacing a faulty switch
b) Replacing noisy fluorescent,
tubes and/or starters
c) Connecting the sensor to a
separate circuit
Note: In most cases where one or more of
the above suggestions have been carried out,
false triggering has been reduced
•
Reposition sensor
OUTPUT
REMAINS
ON
•
Continuously false
triggered
•
Time is set too long.
•
Repositioning the sensor may help
•
Reduce time
OUTPUT
SWITCHES
ON DURING
DAYLIGHT
HOURS
•
LUX control knob is set
to daylight position
•
Turn the LUX control knob to
desired light level setting
SHORTER
DETECTION
DISTANCE
IN DAYLIGHT
SETTINGS
•
Interference by sunlight
•
Re-test at night