ATN NVM14 Скачать руководство пользователя страница 46

Страница: 46 / 60

6-2

6.1. pREVENTIVE MAINTENANCE

A. pURpOSE OF pMCS

pMCS is performed daily when in use to be sure that the NVM-14 is

ready at all times. procedures listed in table 6.1 are a syste-matic

inspection of the NVM-14 that will enable you to discover defects

that might cause the sight to fail on a mission.

b. FREqUENCY OF pERFORMINg pMCS

the frequency of performing pMCS is as follows:

1. Daily when the NVM-14 is in use.

2. When it is removed from the case for any reason.

TABLe 6.1. PReVeNTIVe MAINTeNANCe CheCKS AND SeRVICeS FOR

ATN NVM-14

ITEM

NO.

lOCATION ITEM

TO CheCK/SeR-

VICE

pROCEdURE

NOT FUNCTION

INg AT OpTIMAl

lEVEl IF

Maintenance

open carrying case, inventory

items.

previously recorded faults on

maintenance records.

Not Current.

Fault not

corrected.

MONOCUlAR

optical

Surfaces

Inspect lens for dirt, fingerprint

residue, chips, or cracks. If

necessary, clean and dry lens

with water and lens tissue.

Scratches or

chips hinder

vision with mon-

ocular turned

on, or if cracks

are present.

external

Surfaces

Inspect for cracks or damage.

Scratches and gouges are oK

if operation is not affected

Cracked or

damaged.

Содержание NVM14





























































Результаты поиска

Содержание NVM14

Отзывы:

Похожие инструкции для NVM14

Бренды по названию

Популярные бренды

ATN NVM14, Руководство оператора

Результаты поиска

Содержание NVM14

Отзывы:

Похожие инструкции для NVM14

Бренды по названию

Популярные бренды