Atmel SAM4S Series страница 307 Скачать руководство пользователя | Manualshive

Страница: 307 / 1163

background image

307

11100B–ATARM–31-Jul-12

SAM4S Series [Preliminary]

When the user does not use the internal voltage regulator and wants to supply VDDCORE by an
external supply, it is possible to disable the voltage regulator. Note that it is different from the
Backup mode. Depending on the application, disabling the voltage regulator can reduce power
consumption as the voltage regulator input (VDDIN) is shared with the ADC and DAC. This is
done through ONREG bit in SUPC_MR.

17.4.4

Supply Monitor

The Supply Controller embeds a supply monitor which is located in the VDDIO Power Supply
and which monitors VDDIO power supply.

The supply monitor can be used to prevent the processor from falling into an unpredictable state
if the Main power supply drops below a certain level.

The threshold of the supply monitor is programmable. It can be selected from 1.6V to 3.4V. This
threshold is programmed in the SMTH field of the Supply Controller Supply Monitor Mode Regis-
ter (SUPC_SMMR).

The supply monitor can also be enabled during one slow clock period on every one of either 32,
256 or 2048 slow clock periods, according to the choice of the user. This can be configured by
programming the SMSMPL field in SUPC_SMMR.

Enabling the supply monitor for such reduced times allows to divide the typical supply monitor
power consumption respectively by factors of 32, 256 or 2048, if the user does not need a con-
tinuous monitoring of the VDDIO power supply.

A supply monitor detection can either generate a reset of the core power supply or a wake up of
the core power supply. Generating a core reset when a supply monitor detection occurs is
enabled by writing the SMRSTEN bit to 1 in SUPC_SMMR.

Waking up the core power supply when a supply monitor detection occurs can be enabled by
programming the SMEN bit to 1 in the Supply Controller Wake Up Mode Register
(SUPC_WUMR).

The Supply Controller provides two status bits in the Supply Controller Status Register for the
supply monitor which allows to determine whether the last wake up was due to the supply
monitor:

• The SMOS bit provides real time information, which is updated at each measurement cycle

or updated at each Slow Clock cycle, if the measurement is continuous.

• The SMS bit provides saved information and shows a supply monitor detection has occurred

since the last read of SUPC_SR.

The SMS bit can generate an interrupt if the SMIEN bit is set to 1 in the Supply Controller Supply
Monitor Mode Register (SUPC_SMMR).

«
...
305
306
307
308
309
...
»

Содержание SAM4S Series












































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SAM4S Series

Бренд: J4C Страницы: 4

Elemec3 013-02-0095-002

Бренд: GAI-Tronics Страницы: 12

Бренд: Lawler Страницы: 4

Бренд: QTP Страницы: 2

Бренд: DeLaval Страницы: 102

Бренд: 2N Страницы: 107

Micro850 series

Бренд: Allen-Bradley Страницы: 24

Бренд: Trane Technologies Страницы: 8

Бренд: Sturtevant Richmont Страницы: 73

Бренд: SFC Страницы: 48

Бренд: Satel Страницы: 8

Бренд: Holars AS Страницы: 15

Бренд: ECO POWER Страницы: 2

Бренд: ACL Страницы: 64

Бренд: Zaber Страницы: 23

Бренд: NXP Semiconductors Страницы: 11

L Wired Wall Control

Бренд: Haiku Страницы: 2

Бренд: Rain Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды