Atmel Qmatrix Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 27

Atmel Qmatrix Скачать руководство пользователя страница 19

QTouch Schematic and Layout Checklist [APPLICATION NOTE]

Atmel-42094C-QTouch-Schematic-and-Layout-Checklist-ApplicationNote_072014

19

Figure 3-13. Typical QMatrix Co-Planar (Single Layer) Button

•

Spacing between X and Y Electrodes is at least T/2

The spacing between the X and Y electrode needs to be at least half the front panel thickness. If the front panel

thickness is T then the X-Y gap should be at least T/2. There should be no other tracks running below the X-Y

gap as this can desensitize the key.

In flooded-X designs X-Y separation is determined by the PCB thickness.

Therefore the acceptable front panel thickness is constrained by the thickness

of the PCB used.

Figure 3-14. X-Y Separation and Front Panel Thickness

Single Layer Planar Electrode Layout

Double Layer Flooded-X Electrode Layout

(the field only extends towards touch)

Small X-Y separation = Thin Panel

Large X-Y Separation = Thicker Panel

X

Y

X

T/2

T

Y

X

T

T/2

X

Y

X

T/2

T

Y

X

T

T/2

«
...
17
18
19
20
21
...
»

Содержание Qmatrix




























Отзывы:

Нет отзывов