ATM Cool-stack II Скачать руководство пользователя страница 1

 

25570 Rye Canyon  Rd.                                        Valencia, California  91355 
(661) 294-7999  voice                                                        (661) 294-1115 fax  

 

[email protected]

                                     

www.activethermal.com

 

 

Active Thermal Management 

           

The trusted name in thermal protection 

 
 

Parts list

 – before proceeding, check that you have received all of the 

following:  

 

 

 

 

 

(1) Cool-stack II main chassis 

 

 

 

 

(1) Thermal probe 

 

 

 

 

 

(1) Power supply 

 

 

 

 

 

 

(1) Front panel 

 

 

 

 

Installation of the Cool-stack II

 rack-mount ventilator 

 
 

The Cool-stack II is a very powerful 2U high ventilator, well-suited for removing 
heated air from large rack installations. Some of the features of the Cool-stack II 
are: 
 

  Two-speed operation, with automatic selection of speeds via a thermal probe 

and control assembly; also controllable by external contact closure. 

 

  Sufficient depth (18") to pull heated air from the back of a rack, where it is 

most often generated.   

 

  Six large (120mm/4.7") high-quality fans for quiet ventilation. 

 

  Ability to exhaust heated air through the front, rear, or top, or any combination 

of these for maximum installation flexibility. (With optional exhaust kits)

 

 
 
 

General description: 
 

The Cool-stack II is an exhaust-mode ventilator. It will usually be located at the 
top of a rack, where its six 120mm fans will pull heated air up from the equipment 
below and exhaust it through its front panel. It is extremely quiet in low speed, 
and makes little noise in full speed.  
 

Содержание Cool-stack II






Отзывы: