24
atlona.com
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Commands
The command codes are case sensitive, do not change capitalization, spacing, or lettering.
Command
Feedback
Description
PWX
e.g.
PWSTA
PWX
e.g.
PWON
Turns switcher on, off, or display status
X= ON, OFF, STA
System sta
Model: AT-UHD-CLSO-824
MAC Addr: XX-XX-XX-XX-
XX-XX
Address Type: DHCP
IP: XXX.XXX.XX.XXX
Netmask: 255.255.255.0
Gateway: XXX.XXX.XX.X
HTTP Port: XX
Telnet Port: XX
Firmware: X.X.X
On/Up Time
<dd HH:mm:ss>
:
04 01:09:32
Power Status: PWON
HDVS sta
In 1: AT-HDVS-200TX
IP:XXX.XXX.XX.XX MAC:
XX-XX-XX-XX-XX-XX
In 2: Null
Out: AT-HDVS-200RX
IP:XXX.XXX.XX.XX MAC:
XX-XX-XX-XX-XX-XX
VersionX
X.X.XX
Displays the current firmware version X = MCU, FPGA, OSD, or DSP
Type
AT-UHD-CLSO-824
Displays unit model number
Lock
Lock
Disables front panel buttons
Unlock
Unlock
Enables front panel buttons
All#
x1AVx1, x2AVx2
Resets all inputs to corresponding outputs
x1$ y
e.g.
x2$ off
x1$ y
e.g.
x2$ off
Turns on and off output video y=on, off, or sta
e.g.
Turns video off for output 2
x1All
e.g.
x5All
x1All
e.g.
x5All
Sets input to all outputs
e.g.
Set input 5 to all outputs
x1AVx2
e.g.
x3AVx2
x1AVx2
e.g.
x3AVx2
Switch input to output
e.g.
Set input 3 to output 2
x1AVx1,x2
e.g.
x3AVx1,x2
x1AVx1,x2
e.g.
x3AVx1,x2
Switch input to multiple outputs
e.g.
Swich input 3 to outputs 1 and 2
VGAMSet X
e.g.
VGAMSet comp
VGASet X
e.g.
VGAMSet comp
Sets the analog VGA port to accept VGA (vga) or Component
(comp)
e.g.
Set the VGA port to accept component video
IRON
IRON
Turns the front panel IR receiver on
IROFF
IROFF
Turns the front panel IR receiver off
Statusx1
e.g.
Statusx2
x1AVx3
e.g.
x5AVx2
Shows the input currently connected to the output
e.g.
Show input status of ouptut 2 - Input 5 is currently selected
Status
x4AVx1,x3AVx2
Displays the current input and output routes
SaveY
e.g.
Save2
SaveY
e.g.
Save2
Save the current input/output route to memory
e.g.
Save the current input/output route to memory 2
RecallY
e.g.
Recall4
RecallY
e.g.
Recall4
Recalls the saved input/output memory
e.g.
Recalls the input/output route from memory 4
ClearY
e.g.
Clear3
ClearY
e.g.
Clear3
Erases the input/output route from the selected memory number
e.g.
Removes the saved input/output route from memory 3
Menu[X]
Menu[X]
e.g.
MenuDown
Sets to control OSD interface, [X]: Sw/Up/Down/Left/Right/Info/Sel
e.g.
Select OSD option => MenuSel
Mreset
Mreset
Sets matrix settings back to factory settings
RS232zoneX[command]
e.g.
RS232zone1[turnon]
RS232zoneX[command]
e.g.
RS232zone1[turnon]
Send command through the RS-232 port of the HDBaseT receivers
e.g.
Sends command turnon to the display connected to output 1
When connecting or unconnecting HDBaseT devices to the CLSO (such as HDVS-150) the CLSO will
send query commands to get device type information: RS232zoneX[WP_Display[?]$
CR
]
CR
