manualshive.com logo in svg

Atlona AT-HDVS-210H-TX-WP, Руководство по установке, Страница: 7 / 8

Поделиться
Скачать
Atlona AT-HDVS-210H-TX-WP Скачать руководство пользователя страница 7

7

Installation Guide

AT-HDVS-210H-TX-WP

Resetting to Factory-Default Settings

Resetting the AT-HDVS-210H-TX-WP requires that the front faceplate be removed. Before 

removing the faceplate, the AT-HDVS-210H-TX-WP must be disassembled from the electrical box 

or mud ring.  A small Phillips-head screwdriver is required to remove the faceplate.

1.  Remove the faceplate from the AT-HDVS-210H-TX-WP.  Refer to the section 

Faceplate 

Removal and Assembly

 for more information.

2.  Press and release the 

Reset

 button.

3.  Reassemble the faceplate to the front of the AT-HDVS-210H-TX-WP and reinstall into the 

electrical box or mud ring.

Accessing the webGUI

The AT-HDVS-210H-TX-WP includes a built-in webGUI, which allows easy management and 

control of all features.  Follow the instructions below to access the webGUI.

1.  Make sure that an Ethernet cable is connected between the 

LAN

 port on the receiver unit 

and the network.

2.  Launch a web browser and enter the IP address of the AT-HDVS-210H-TX-WP.  If the default 

static IP address is being used, enter 

192.168.1.254

.

3.  The 

Login

 page will be displayed.

4.  Enter the following information on the 

Login

 page.

 

 

Login:  

root

 

Password:  

 

Atlona

 

5.  Click the 

Login

 button.

6.  Refer to User Manual for detailed operation of the webGUI.

Содержание AT-HDVS-210H-TX-WP









Отзывы:

Нет отзывов