manualshive.com logo in svg

Atlona AT-HDVS-210H-TX-WP, Руководство по установке, Страница: 6 / 8

Поделиться
Скачать
Atlona AT-HDVS-210H-TX-WP Скачать руководство пользователя страница 6

6

Installation Guide

AT-HDVS-210H-TX-WP

By default, the AT-HDVS-210H-TX-WP is set to DHCP mode, allowing a DHCP server (if present) 

to assign the unit an IP address.  If a DHCP server is not found within 15 seconds, the IP address 

of the unit will be set to 

0.0.0.0

. If a static IP address is desired, the IP address of 

192.168.1.254

 

is used by default.  Refer to the User Manual for more information on IP configuration.

IP Configuration

Switching the IP mode

Switching the IP mode requires that the faceplate be removed.  Refer to 

Faceplate Removal and 

Assembly

, for more information.

1.  Make sure the AT-HDVS-210H-TX-WP is powered, by connecting it to a PoE-compatible 

receiver, such as the AT-HDVS-200-RX.  Power is supplied by the receiver over HDBaseT.

2.  Remove the faceplate.
3.  Press and hold the 

Reset

 button for approximately 15 seconds.  Release the 

Reset

 button 

once the 

PWR

 LED indicator begins to flash.  The number of flashes will indicate the 

currently selected IP mode.

4.  Once the desired IP mode has been selected, use an IP scanner to locate the AT-HDVS-

210H-TX-WP on the network.  Use the MAC address, located on the back of the unit, to 

identify the unit within the IP scanner.

PWR LED flashes

Description

Two

Static IP mode

Four

DHCP mode

IP Mode / Reset button

PWR LED indicator

Содержание AT-HDVS-210H-TX-WP









Отзывы:

Нет отзывов