Atlas Copco XAS 185 KDU T4F HOP Скачать руководство пользователя страница 39

Страница: 39 / 62

- 39 -

Set the Auto Load Function

Press the ‘Settings View button’
•

Scroll to 1000 GENERAL SETTINGS

•

Press ‘Enter button’

•

Scroll to 1160 Auto Load

•

Enter the FUNCTION menu

•

Scroll to Auto Load setting

•

Press ‘Enter button’.

Now the Auto Load function is active, and as soon as the

unit is Ready to Start, the display will show the Auto Load

icon
If ‘Function’ is set to ‘Off’, both Auto Load and Auto No-

Load functions are disabled.
If ‘Function’ is set to ‘Auto Load’, then only the Auto

Load function is enabled. In this mode, the machine will

remain loaded regardless of Operation Mode Command

setting.
If ‘Function’ is set to ‘Auto No-Load’, then only the Auto

No-Load function is enabled. In this mode, the loaded

machine will operate loaded for the time configured in

‘Timer’ before reverting back to the No Load state.
If ‘Function’ is set to ‘Auto No-Load + Reload’, then both

automatic loading and unloading functionalities are

enabled, and the machine will start and stop as dictated by

the sensor’s pressure set point and timer setting.

Auto Start/Auto Stop

Parameter 1170 – Auto Start, 1180 – Auto Stop

If ‘Enable’ is set to ‘On’, the machine will attempt to start

if the measured value of the selected sensor goes below the

configured ‘Pressure’ for an elapsed time configured by

‘Delay’.

When ‘Enable’ is set to ‘On’, ‘Function’ (parameter 1160)

is automatically set to ‘Auto Load’.

If you are using an external sensor to control automatic

functionality, the sensor’s pressure values at 0.5V and

4.5V must be specified in 13180 parameter.

If ‘Function’ is set to ‘On’, the machine engine will stop

after being in Loaded Sequence for the elapsed time

configured in ‘Timer’.

Once desired Auto Load, Auto Start, Auto Stop and

external sensor range (if applicable) is defined, finally go

to parameter 1100 and set the operation mode to

AUTOMATIC, as the machine may start prematurely if

this parameter is set earlier.

Once set to AUTOMATIC, the Automatic operation icon

appears.

If the automatic Operation Mode is active, but both Auto

Start and Auto Stop are disabled, a red slash appears of the

Automatic operation icon to indicate the machine will not

perform automatically.

Suggested Atlas Copco transducers

Parameters 1160 – 1180 can be configured

in any order and will remain inactive until

Operation

Mode

Command

(parameter1100)

configured

‘Automatic’. Parameter 1100 must be

configured last or the machine may start

prematurely if this parameter is set earlier.

Atlas Copco Model No.

Pressure (in bar)

1089957963

0 to 25

1089957964

0 to 50

1089957971

-1 to 5

1089957972

-1 to 17

1089957974

0 to 17

1089957975

0 to 35

1089957976

0 to 50

Содержание XAS 185 KDU T4F HOP































































Результаты поиска

Содержание XAS 185 KDU T4F HOP

Отзывы:

Бренды по названию

Популярные бренды

Atlas Copco XAS 185 KDU T4F HOP, Инструкция по эксплуатации

Результаты поиска

Содержание XAS 185 KDU T4F HOP

Отзывы:

Бренды по названию

Популярные бренды