Atlas Copco XAS 185 KDU T4F HOP Скачать руководство пользователя страница 37

Страница: 37 / 62

- 37 -

TURNING REGENERATION BACK TO AUTO

Machine is not running:

Power the controller down. At next power up, the DPF

Regeneration settings will be back to default, and an

Automatic DPF Regeneration will take place at the

soonest appropriate moment.

Machine is running:

•

Make sure parameter '1142 ECU DPF REGENERA

TION ENABLE' is set to "ON"

•

Scroll down and Enter the 'MODE' parameter

•

Scroll down and Enter the 'AUTOMATIC' setting

•

Press the Back button 3 times to get back to the Main

view

FORCE DPF REGENERATION

Machine is running:

•

Press the Settings View Button

•

Enter the '1000 GENERAL SETTINGS' menu

•

Go to parameter '1130 STATIONARY REGENERA

TION'

•

Scroll to Enable and change to "ON"

•

Go to parameter '1140 ECU DPF REGENERATION'

•

Scroll to Enable and change to "ON"

SERVICE REGENERATION

Machine is running:

•

Press the Settings View Button

•

Enter the '7000 ENGINE' menu

•

Go to parameter '7140 SERVICE REGENERAION'

•

Scroll to Enable and change to "ON"

SETTINGS

For buttons to be used see “Control Panel”

Acknowledge an Alarm

If an alarm becomes active, for example a Low Fuel Level

Warning:

then this alarm can be acknowledged by pressing the
ENTER button. If the fuel level is still low, the view
will change to:

As soon as the fuel level is higher than the warning level,

the alarm icon will automatically disappear.
As long as there is an alarm icon in the middle of the

bottom part of the view, all active acknowledged /

unacknowledged alarms can be seen by pressing the

ALARM VIEW button
Pressing the ALARM VIEW button again, will bring you

back to the Main View.

Unit will not regenerate if soot level is not

high enough.

Unit will not regenerate if soot level is not

high enough.

Содержание XAS 185 KDU T4F HOP































































Результаты поиска

Содержание XAS 185 KDU T4F HOP

Отзывы:

Atlas Copco XAS 185 KDU T4F HOP, Инструкция по эксплуатации, Страница: 37 / 62

Результаты поиска

Содержание XAS 185 KDU T4F HOP

Отзывы: