manualshive.com logo in svg

Atlas Copco GA 11 VSD, Инструкция

Поделиться
Скачать
Atlas Copco GA 11 VSD Скачать руководство пользователя страница 28

3.9

Measured data menu

Control panel

Function

To call up information regarding the actually measured data and the status of some inputs such
as the motor overload protection. Consult the menu flow in section 

Control programs.

Procedure

Starting from the Main screen (see 

Main screen menu

):

• Press the key ‘Menu’ (F1).
• Press the arrow down key (1) until ‘Measured data’ is followed by a horizontal arrow.
• Activate the menu by pressing the tabulator key (2).
• By pressing the scroll keys (1), a number of actually measured data can be found.
• If one of the sensors is linked to a shut-down, service or warning function, both the actually

measured value as well as the corresponding shut-down, warning or service level can be
called up by pressing key (2).

3.10 Counters menu

Control panel

Function

To call up:

• The loaded hours
• The number of motor starts
• The number of hours the regulator (module) has been under tension
• The accumulated volume

Instruction book

26

API161475

Содержание GA 11 VSD





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды