Atlas Copco Dynapac F1800C страница 284 Скачать руководство пользователя

Страница: 284 / 318

F 82.18 10

Drive belts

Checking / adjusting belt tension:

- The tension of the belt can only be adjusted using a pre-tensioning test device.

Checking belt tension

The tension of each belt must be
inspected with a pretension check-
ing instrument.

Specified tension:

- In case of initial assembly: 550N
- After running-in period /

maintenance interval: 400N

Instructions for checking tightness in the
pretention measuring instrument instructions.

A pretention measuring instrument can be ordered under Article No. 4753200045!

If necessary, adjust the belt tension:

- Unfasten lock nut (A) from the clamp-

ing lock.

- Adjust belt tension to the correct val-

ues by turning the clamping lock (B).

- Tighten the lock nut (A) again.

Further instructions for checking of ten-
sion - see description of the pre-tension-
ing test device.

A belt pre-tensioning test device can be
ordered from Dynapac as a spare part!
Item number on request.

Riemensp.tif

Содержание Dynapac F1800C































































































































































































































































































































Результаты поиска

Содержание Dynapac F1800C

Отзывы:

Похожие инструкции для Dynapac F1800C

Бренды по названию

Популярные бренды

Atlas Copco Dynapac F1800C, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Dynapac F1800C

Отзывы:

Похожие инструкции для Dynapac F1800C

Бренды по названию

Популярные бренды