Atlantic WOYG112LHT Скачать руководство пользователя

Страница: 73 / 92

9 Fault diagnostic

Depending on whether the fault is on the outdoor unit or

the hydraulic module, the fault may be advised by the

digital display or the LED on the interface boards.

Before carrying out any work, ensure that the general electrical power supply is switched off.

Antifreeze protection is not provided when the heat pump is not powered up.

9 .1 Fault display on the hydraulic module

The faults or breakdowns of the hydraulic module are

advised on the display unit of the user interface.

The light comes on during an operating anomaly.
The display shows the

symbol.

Press the

button to obtain the details of the origin

of the fault

When the error is resolved, the faults are reset

automatically.
The appliance may stop and restart automatically when

the problem disappears.

Maintenance code

Code 22 indicates a low hydraulic pressure between

0.8 and 0.5 bar. Add water until the hydraulic system

pressure reaches 1.5 bar.

Safety mechanism

Certain anomalies will cause the boiler's safety

mechanism to switch on (error codes 78, 128 and 133).

In this case, reset the boiler by pressing the red button

on the side of the control panel (see

figure 63

Note:
An anomaly on the outdoor unit may case an error

signal (the "Err" light comes on).
In this case:

the domestic hot water will be produced,

the heating will be stopped.

Alert the heating engineer

Hydraulic module:

Heat pump regulator faults (RVS) visible on the digital display.

Error number Error description

Error position

Heat pump

operation despite

the error

No connection.

The polarity of the ambient

sensor has not been respected.

Outdoor sensor.

Yes

Heat pump start sensor temperature error.

B21

Yes

Heat pump start sensor temperature error.

B71

Yes

DHW temperature sensor.

Yes

Ambient sensor 1.

Yes

Ambient sensor 2.

Yes

105

Maintenance message.

Yes

121

Heating circuit 1 start temperature not reached.

Yes

122

Heating circuit 1 start temperature not reached.

Yes

127

Anti-legionella temperature not reached.

Yes

369

External fault (safety device)

370

Outdoor unit error

(during a start-up phase, see § "Commissioning").

See below and

page 76

page 77

figure 63 -

Reset button

Installation and commissioning instructions "1485 - EN"

- 73 -

Heat pump alféa hybrid duo gas

Содержание WOYG112LHT





























































































Результаты поиска

Содержание WOYG112LHT

Отзывы:

Похожие инструкции для WOYG112LHT

Бренды по названию

Популярные бренды

Atlantic WOYG112LHT, Инструкции по установке и вводу в эксплуатацию

Результаты поиска

Содержание WOYG112LHT

Отзывы:

Похожие инструкции для WOYG112LHT

Бренды по названию

Популярные бренды