Atlantic WOYG112LHT Скачать руководство пользователя

Страница: 77 / 92

figure 65 - Location of switches and diodes

on 3-phase outdoor unit

Diodes

and switches

Terminal

block

SW2

SW3

SW4

SW5

(1)

(2)

(3)

(4)

figure 66 - LED display on the 3-phase outdoor unit

9 .3 Faults displayed

on the 3-phase outdoor unit

To access the electronic board, you must remove the

front (right-hand) facing from the outdoor unit.
Faults are coded by diode flashes.

When an error occurs:

The diode "

ERROR

" (2) blinks.

Press once on the switch "

ENTER

" (SW4).

The "

ERROR

" (2) diode blinks several times depending

on the error's type

(see below).

Diode display

Error description

1 Flash

Error on series communication return.

2 Flashes

Discharge thermistor temperature sensor error.

3 Flashes

Error on pressure switch sensor.

4 Flashes

Error on exchanger temperature sensor.

5 Flashes

Error on exchanger temperature sensor.

6 Flashes

Error on pressure regulator temperature sensor.

7 Flashes

Error on outdoor temperature sensor.

8 Flashes

Error on compressor temperature sensor.

9 Flashes

Error on radiator temperature sensor inverter.

10 Flashes

Error on radiator temperature sensor P.F.C.

11 Flashes

Discharge thermistor protection (permanent stop).

12 Flashes

Discharge thermistor protection (permanent stop).

13 Flashes

Current sensor error (permanent stop).

14 Flashes

Detection error for the position of the compressor rotor (permanent stop).

15 Flashes

Compressor start error (permanent stop).

16 Flashes

Error on fan 1 motor (permanent stop).

17 Flashes

Error on fan 2 motor (permanent stop).

18 Flashes

Inverter error.

19 Flashes

P F C error

20 Flashes

Abnormal low pressure.

21 Flashes

Connection error with the hydraulic module.

22 Flashes

Hydraulic module anomaly.

Installation and commissioning instructions "1485 - EN"

- 77 -

Heat pump alféa hybrid duo gas

Содержание WOYG112LHT





























































































Результаты поиска

Содержание WOYG112LHT

Отзывы:

Похожие инструкции для WOYG112LHT

Бренды по названию

Популярные бренды

Atlantic WOYG112LHT, Инструкции по установке и вводу в эксплуатацию

Результаты поиска

Содержание WOYG112LHT

Отзывы:

Похожие инструкции для WOYG112LHT

Бренды по названию

Популярные бренды