background image

31

Wiring diagram for the heating panel

-

Cut off the power supply and connect the wires as shown in the following diagram:

- You can connect the pilot wire if your home is equipped with a programming unit or controller.

In this case, make the following checks according the selected mode (

Comfort, Eco, etc.

) to that the

programming instructions are being transmitted correctly:

COMFORT

ECO

FROST

SWITCH-OFF

OF HEATING

AND POWER

CUT-OFF

COMFORT

-1°C

COMFORT

-2°C

SIGNAL TO BE 
TRANSMITTED

MEASUREMENT
BETWEEN THE
PILOT WIRE
AND NEUTRAL

0 Volt

230 Volts

-115 Volts

negative

+115 Volts

positive

230 Volts

for 3 s

230 volts

for 7 s

C

ONNECTING THE DEVICE

Connection rules and regulations

- The device must be supplied with 230V single-phase current at 50Hz.
- The device’s power supply must be directly connected to the main supply after the circuit breaker

without any intermediate switch.

- The device’s power cable must be connected to the main supply via a connection box. In damp areas,

such as bathrooms and kitchens, the connection box must be installed at least 25cm above the floor.

An Earth connection is prohibited. Do not connect the pilot wire (black wire) to Earth.

- The installation must be fitted with an all-pole cut-off switch with a contact opening distance of at least

3mm. 

- If the power cable is damaged, it must only be replaced by an electrician.
- If you are using the pilot wire and it is protected by a 30mA differential (

e.g.: bathroom use

), the pilot

wire’s power supply must also be protected on this differential. 

GB

Содержание Radiant panel heater - Horizontal and vertical





























Отзывы: