Atlanta Attachment Company 1390BX Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 172

background image

Technical Manual & Parts Lists

17

Top Film Loading

The standard 1390B machine comes with a Top Film Roll storage rack that can handle up to (4)

12” diameter x 120” long rolls of plastic film.

Important note! The film rolls must be loaded such that they unwind counter-clockwise, looking
from the left side of the machine (see “Film Routing” on page 19).

Besides the standard top film roll rack, Atlanta Attachment Company offers two options to aid in

the loading and storage of the Top Film Rolls:
1. Crane option - For installations with a limited space on each side of the machine. The crane lifting
mechanism can be swiveled 360 degrees from the shown position this allows any orientation of rolls on
the floor next to the machine.
2. Extended Top Roll Rack option - For installations where the rolls can only be loaded from the Output
End of the machine. This option allows loading of up to (18) 12” diameter rolls on top of the machine.
The Extended Roll Rack option excludes the Crane option due to space limitations on top of the
machine.

If the side space is not limited, an operator can load the Top Film using a standard fork lift.

The standard Top Film Roll Rack has (2) roll film release rods to allow the rolls to be advanced one at a
time.

Figure 9

«
...
23
24
25
26
27
...
»

Содержание 1390BX













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1390BX

Бренд: MacDon Страницы: 17

Бренд: Olympus Страницы: 50

Бренд: VAHVA Страницы: 19

Crouse-hinds series

Бренд: Eaton Страницы: 32

Бренд: habitat et jardin Страницы: 11

Бренд: Haag-Streit Страницы: 16

Бренд: Labnet Страницы: 12

Accublock D1301

Бренд: Labnet Страницы: 13

Бренд: laerdal Страницы: 8

Бренд: LAHTI PRO Страницы: 16

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 8

Бренд: Vahle Страницы: 36

Бренд: Vahle Страницы: 20

Бренд: Vacon Страницы: 102

Бренд: MÄDLER Страницы: 4

Бренд: JBM Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды