SWITCHABLE MESSAGE WAITING
There are three versions of message waiting
indication supported within the Berkshire 600
telephone (MW 3, 8 and 10). This selection is made
via a 4 position switch located to the rear of the
phone, indicated by the letters ‘MW’.
A ‘Ring Indicator’ position is provided that has the
additional bene
fi
t of being activated by short ring
burst MW signals - see website for details.
In all cases, an LED in the top right hand corner
of the telephone is used to indicate the selected
functions and incoming calls.
Any questions you may have should be directed
in the
fi
rst instance to your telephone supplier with
details of your PABX.
Further concerns may also be addressed by calling
our Technical Support Dept. on 0845 421 0730 or
visiting our website, www.atltelecom.com
MODEM PORTS
Your Berkshire 600 comes with two modem ports
(BS6312 and RJ11) typically used for a PC modem,
or as points of connection for additional telephones.
HEARING AID COMPATIBILITY
For hearing aid users, an inductive coupler has
been installed in the handset of the Berkshire 600,
to improve audible ef
fi
ciency.
Installation Notes
MESSAGE WAITING
MW3 is used by systems that use high voltage
DC signalling. MW8/10 however use line reversal
methods to indicate that a message is present.
PAUSE TIME ADJUSTMENT
The ‘pause’ key may be con
fi
gured via the keypad to
represent 1 of 4 time periods (1~4 sec.). In all cases,
lift the handset, press SET, PAUSE, followed by a
numeric key (1~4) to set the pause time, replace
handset. Default = 1s.
TBR TIME ADJUSTMENT
Transfer break times may be adjusted from
100~600ms. in increments of 100ms. First con
fi
rm
that the 2 position switch, identi
fi
ed as RECALL on
the rear of the phone, is set to the ‘T’ position. Lift
the handset, press SET, TRANSFER, followed by a
numeric key (1~6), replace the handset. Default =
100ms.
PROGRAMMING PORT
The Berkshire 600 has an unidenti
fi
ed port,
alongside the other con
fi
guration switches, at the
rear of the telephone. Programming of this port is
limited to technicians trained in its use.
Preparing to use your
Berkshire 600
INITIAL CHECK
Our telephones are checked, tested and leave us
in perfect condition. If yours is damaged, please
return it to your supplier with proof of purchase, for
a replacement.
TELEPHONE NUMBER LABEL
The telephone incorporates a label underneath the
handset for recording frequently used telephone
numbers. To remove the plastic cover, operate the
release clip with your thumb nail and hinge upward.
CONNECTION
The Berkshire 600 telephone can be connected
either to a Direct Exchange Line, or as an extension
to a compatible company exchange (PABX).
HANDSET CORD
This cord will require connection between the
telephone and handset. Take any end of the handset
cord, and locate the port marked ‘HANDSET’ on the
left hand side of the Berkshire 600, and simply push
to locate. Connect the other end to the base of the
handset to complete.
LINECORDS
The Berkshire 600 arrives with two line cords for
customer selection. Select your required linecord
(standard BS6312 BT-socket, or RJ45 socket for
category 5 installations). The rear of the telephone
has a port marked ‘LINE’, plug your selected
linecord into this port
fi
rst, and the other end to your
telephone line termination point. An RJ11 line cord is
available as an option, ask your supplier for details.
For certain non UK customers, the RJ11 linecord
may be included as standard.
WALL AND DESK MOUNTING KITS
A wall mounting kit is available as an option, please
contact your supplier for further information.
Using your Berkshire 600
with the Handset
RECEIVING CALLS
Incoming calls will be announced by the audible
ringer and
fl
ashing LED. To answer the call, simply
lift the handset. This will also activate the display,
showing time, date, and call time. Refer to the
LCD section of this guide for more detail on how
to con
fi
gure, including adjustment of the viewing
angle.
ADJUSTING YOUR RINGER-VOLUME
The ringer volume is controlled by a 3 position switch
located at the rear of the telephone, and indicated by
the word ‘ringer’. Moving through the settings from
left to right they are HIGH, MED and LOW.
ADJUSTING YOUR RINGER PITCH
The ringer pitch control is also a 3 position switch
located at the rear of the telephone, and indicated
by the words ‘RINGER PITCH’. Settings from left to
right are HIGH, MED and LOW.
MAKING A CALL VIA THE HANDSET
Pick up the handset and listen for dial tone
Dial the required telephone number
(Note: making external calls from a company
exchange (PABX) requires the number to be pre
fi
xed
by an access digit, notmally ‘9’)
USING YOUR BERKSHIRE 600 WITH HEADSET
CONNECTING THE HEADSET
To connect the headset, insert the plug on the
headset cord into the socket marked HEADSET on
the left hand side of the telephone.
NOTE: Headsets used with this telephone must
comply with the standard EN6095
RECEIVING CALLS
When your telephone rings, the default path for the
call is to the handset. To receive it on the headset,
press HEADSET button once and the call is switched
to the headset. This action will be con
fi
rmed by LED
indication within the headset button. At the end of
the call, press the HEADSET button a second time
to turn the headset off.
•
•
Содержание Berkshire 600
Страница 2: ...H If co so N TR...
