Atkinson Electronics PVCM40D-MPT Скачать руководство пользователя страница 11

www.atkinsonelectronics.com

                                                                                                                 Circuit Board Division 

800.261.3602 

 

Revised 05/19 

 

 

Charging Mode LED Definitions 

 

The Charge Mode LED indicates which of the three main PWM charge stages the controller is in: 

 

Bulk charge stage - The LED is lit red 

 

Absorption charge stage - The LED blinks red 

 

Float charge stage - The LED is lit green 

If  the  charge  mode  LED  is  not  lit,  it  means  that  there  is  not  enough  sun  light  to  charge  the  battery, 

controller is in night mode. 

Charge Type LED Definitions 

 

The charge type LED indicates the types of charge the controller is in: 

Soft Charge - The LED is lit red.  

 

Soft charge is set when the battery voltage drops below 11.0VDC. 

 

Once battery voltage climes above 11.5VDC it turns off. 

Equalization Conditioning - The LED blinks blue. 

 

Equalization flag is set when the battery voltage drops below 12.1VDC three times in a 14 day 

period. 

 

It is continuously lit while in equalization mode. 

Auto Boost - The LED blinks magenta when the auto boost flag is set. 

 

It is continuously lit during the bulk and absorption phase of the boost cycle. It turns off once the 

controller returns to float stage. 

The charge type LED is not normally lit, if any of the above conditions occurs, it will then blink or light 

continuously, indicating the charge it’s in. 
While in the float charge stage, if the load currents exceeds the solar charge current and the controller 

can’t maintain the float voltage, the charge mode LED will blink green. If the battery voltage drops below 

13VDC for 5 minutes the controller sets its auto boost flag and blinks the charge type LED magenta. Once 
the load is reduced or the solar charge current increases and battery voltage returns to float voltage, the 

charge type LED turns on, until it completes the auto boost charge cycle. 

Battery Status LED Definitions 

 

The battery status LED indicates six levels of charge: full, high, medium, partial, low and empty. 

 

 

COLOR 

POWER 

BATTERY SOC 

VDC 

 

Lit Green 

Full 

100% 

>12.8 

  Blinking Green  High 

95 to 70% 

12.8 down to  

12.4 

 

Lit Orange 

Medium 

70 to 50% 

12.4 down to 12.1 

 

Blinking Orange 

Partial 

50 to 30% 

12.1 down to 11.8 

 

Lit Red 

Low 

30 to 10% 

11.8 down to 11.5 

 

Blinking Red 

Empty 

0% 

<11.5 

Содержание PVCM40D-MPT


























Отзывы: