15
Assembling the switch
Fasten the switch (12) onto the switch base (c).
Assembling the recuperating bolt and the jigging device
Screw the recuperating bolt (16) hand-tight to the leg of the tilt table
(7) Tighten the nut M8 firmly and slacken it then by a half turn.
Fold the frame (8) apart and fix the braces (9).
[2x screw M8x40, 4x washer Ø 8, 2x nut M8]
Montieren Sie die Wippe (7) an das Gestell (8).
[2x screw M8x70, 6x washer Ø 8, 2x nut M8]
Tighten the screw only by hand and then slacken the nuts by a half
turn.
The guide must move freely.
Assembling the saw blade casing and the saw blade
Attach the inner saw blade casing (1) to the motor base (c).
Slide the rear saw blade flange (21) on the motor shaft.
(17)
Danger of cutting! Wear gloves.
Mount the saw blade (22)
Pay attention to the saw blade’s sense of rotation(note the
arrow on the saw blade and on the saw blade casing).
Slide the front saw blade flange (23) on the motor shaft . Schieben
Sie den vorderen Sägeblattflansch (23) auf die Motorwelle. Secure
these parts using the locking nut [M20x1.5].
Tighten the nut using the open-end wrench (25) and ring spanner
(26).
Store the wrenches/spanners for future use.
Bolt down the outside saw blade casing (2).
Assembling the recuperating bolt
Pull out the securing cotter pin (16c) and remove one of the two
washers (16d).
Fold up the tilt table (7).
Insert the recuperating bolt (16a) through the hole of the bracket
(d).
The recuperating spring (16b) and the washer must rest on
the bracket.
Fix the bolt (16a) using the washer and the securing cotter pin
(16c).
Assembling the safety chain
Fasten the safety chain (10) on the frame.
Fasten the locking plate
Fasten the locking plate (13) to the inside saw blade cover (21).
Mount the limit plate
Mount the limiting plate (3) to the saw blade casings (1 / 2).
Mount the safety flap
Fasten the safety flap (4) to the rear walls (18 / 20).
Assembling the support extension
Insert the support extension (6) into the jigging device. Secure the
support extension with the wing screw (15)
Make sure after mounting that all screws are tightened firmly.
Before the first start-up
To achieve flawless functioning of the machine, please follow the
instructions listed:
Place the saw at a location which meets following conditions:
outdoor
secured against slipping
free of vibrations
even
free of tripping hazards
adequate light
To ensure a safer foothold when working with the saw secure the saw
against rolling away.
Before each use, check
connection cables for defects (cracks, cuts, etc.)
Do not use any defective cables.
that the plastics insert is in a proper condition
the saw blade for flawless condition
the functioning of the jigging device
Do not use any cracked saw blades or such that have changed their
shape.
Do not use any saw blades made of HSS steel.
Immediately replace a worn or damaged plastics inserts.
Assume the correct work posture. Stand in front of the operating side
frontally to the saw blade line.
Location
The machine must be placed in a stable manner on a
solid and flat surface (such as concrete floor). To ensure the
stability, it is necessary to screw the machine with four
dowels and screws (at least Ø10 x 80) on the ground.
Start-up
Rotational direction of the saw blade
Ensure that the rotational direction of the saw blade is the
same as the rotational direction given on the saw blade casing
(1).
Selection of saw blades
Consider when selecting the saw blade, that no edgeless or
damaged saw blades are used and that the diameter of the
blade location hole is 30 mm (note the nameplate on the
machine).
Mains connection
Compare the voltage given on the machine model plate e.g. 230 V
with the mains voltage and connect the machine to the relevant
and properly earthed plug.
Use a shockproof plug, mains voltage 230 V with residual
current circuit breaker (FI switch 30 mA).
Main fuse
16 A inert
